89 lines
2.9 KiB
C++
89 lines
2.9 KiB
C++
// camera_init.ino — minimum reproducer for "OV2640 emulation needed".
|
|
//
|
|
// Runs through the full upstream esp32-camera init dance and prints
|
|
// either the chip ID + a single-frame size or a clear error code.
|
|
//
|
|
// Today, under Velxio, this sketch hangs at esp_camera_init() because
|
|
// the SCCB I²C probe never gets an ack from a (non-existent) sensor.
|
|
// When the shim from autosearch/04_proposed_architecture.md ships,
|
|
// this sketch should print "got frame: N bytes" within ~5 s of boot.
|
|
//
|
|
// Pinout below matches the AI-Thinker ESP32-CAM, the variant Velxio
|
|
// renders. Don't change pin numbers — Layer-2 of the test suite checks
|
|
// that this sketch matches the board the simulator presents.
|
|
|
|
#include "esp_camera.h"
|
|
|
|
#define PWDN_GPIO_NUM 32
|
|
#define RESET_GPIO_NUM -1
|
|
#define XCLK_GPIO_NUM 0
|
|
#define SIOD_GPIO_NUM 26
|
|
#define SIOC_GPIO_NUM 27
|
|
#define Y9_GPIO_NUM 35
|
|
#define Y8_GPIO_NUM 34
|
|
#define Y7_GPIO_NUM 39
|
|
#define Y6_GPIO_NUM 36
|
|
#define Y5_GPIO_NUM 21
|
|
#define Y4_GPIO_NUM 19
|
|
#define Y3_GPIO_NUM 18
|
|
#define Y2_GPIO_NUM 5
|
|
#define VSYNC_GPIO_NUM 25
|
|
#define HREF_GPIO_NUM 23
|
|
#define PCLK_GPIO_NUM 22
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
delay(1000);
|
|
Serial.println("velxio-esp32-cam-test boot");
|
|
|
|
camera_config_t cfg = {};
|
|
cfg.ledc_channel = LEDC_CHANNEL_0;
|
|
cfg.ledc_timer = LEDC_TIMER_0;
|
|
cfg.pin_d0 = Y2_GPIO_NUM;
|
|
cfg.pin_d1 = Y3_GPIO_NUM;
|
|
cfg.pin_d2 = Y4_GPIO_NUM;
|
|
cfg.pin_d3 = Y5_GPIO_NUM;
|
|
cfg.pin_d4 = Y6_GPIO_NUM;
|
|
cfg.pin_d5 = Y7_GPIO_NUM;
|
|
cfg.pin_d6 = Y8_GPIO_NUM;
|
|
cfg.pin_d7 = Y9_GPIO_NUM;
|
|
cfg.pin_xclk = XCLK_GPIO_NUM;
|
|
cfg.pin_pclk = PCLK_GPIO_NUM;
|
|
cfg.pin_vsync = VSYNC_GPIO_NUM;
|
|
cfg.pin_href = HREF_GPIO_NUM;
|
|
cfg.pin_sccb_sda = SIOD_GPIO_NUM;
|
|
cfg.pin_sccb_scl = SIOC_GPIO_NUM;
|
|
cfg.pin_pwdn = PWDN_GPIO_NUM;
|
|
cfg.pin_reset = RESET_GPIO_NUM;
|
|
cfg.xclk_freq_hz = 20000000;
|
|
cfg.pixel_format = PIXFORMAT_JPEG;
|
|
cfg.frame_size = FRAMESIZE_QVGA; // 320x240 — keeps WS bandwidth low
|
|
cfg.jpeg_quality = 12;
|
|
cfg.fb_count = 1;
|
|
// Default fb_location is CAMERA_FB_IN_PSRAM, which fails under QEMU
|
|
// because we don't emulate the AI-Thinker board's external PSRAM.
|
|
// DRAM has enough contiguous DMA-capable memory for QVGA JPEG (~30 KB).
|
|
cfg.fb_location = CAMERA_FB_IN_DRAM;
|
|
|
|
esp_err_t err = esp_camera_init(&cfg);
|
|
if (err != ESP_OK) {
|
|
Serial.printf("camera_init failed: 0x%x\n", err);
|
|
return;
|
|
}
|
|
Serial.println("camera_init ok");
|
|
}
|
|
|
|
void loop() {
|
|
camera_fb_t* fb = esp_camera_fb_get();
|
|
if (!fb) {
|
|
Serial.println("fb_get returned NULL");
|
|
delay(500);
|
|
return;
|
|
}
|
|
Serial.printf("got frame: %u bytes %ux%u fmt=%d\n",
|
|
(unsigned)fb->len, (unsigned)fb->width,
|
|
(unsigned)fb->height, (int)fb->format);
|
|
esp_camera_fb_return(fb);
|
|
delay(500);
|
|
}
|