Companion chip for 8086 minimum-mode boards that demultiplexes
AD0..AD15 → A0..A15 under control of ALE. ~80 LOC clean-room from
the public Intel 8282/8283 datasheet.
Pin contract (20-pin DIP): DI0..7 in, DO0..7 out, STB strobe, OE̅
output enable, VCC, GND. Behaviour:
STB=1, OE̅=0 → DO follows DI (transparent)
STB falling → latch held while STB=0
OE̅=1 → DO pins released (modelled as VX_INPUT)
Tests: 4/4 passing (pin contract, transparent mode, latch hold,
output enable). Brings test_intel total to 47 passing.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
The two earliest commercial Intel CPUs as velxio custom chips:
- 4004.c (~150 LOC): 16-pin DIP, 8-phase frame (A1..X3), SYNC at A1
with PC nibble walk on D0..D3 (low-first per MCS-4 Fig. 2), CMROM
strobe during M1. ISA decoded as NOP for now — full 46-instruction
set deferred to ISA phase.
- 4040.c (~250 LOC): 24-pin DIP per MCS-40 pp. 1-5/1-6 (STP/STPA/INT/
INTA/CY/dual CMROM/dual standby Vdd). 4004-compatible bus + STP
latched at M2 → STPA asserts at X3 + INT forced JMS to PC=0x003.
14 new opcodes decoded as NOP for now.
Test refinements (analogous to bootCpu fix from 8080 work):
- bootChip no longer advances time post-RESET so first observed cycle
starts at A1 of cycle 0 with PC=0.
- SYNC sampler latches on first edge (was over-collecting on
subsequent SYNC pulses).
- 4040 test renamed STOP→STP, STOPACK→STPA per MCS-40 datasheet pin
names; added INTA, CY, VDD1, VDD2 pins; SYNC-stops assertion
removed (manual: STOP mode keeps clock and SYNC running).
Brings test_intel suite from 37 to 43 passing tests; 0 failures;
remaining 3 active are 8086 (deferred), 29 todo are intentional
deferred integration tests.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Authoritative spec docs cite Intel MCS-4 (Feb 1973) and MCS-40 (Nov 1974)
manuals page-by-page. Reference-implementations doc surveys four
permissively-licensed open-source emulators (markablov/i40xx,
Kostu96/K4004, lpg2709/emulator-Intel-4004, alshapton/Pyntel4004) for
cross-validation, explicitly excluding GPL sources (MAME mcs40,
carlini/intel-4004-in-4004-bytes-of-c).
Critical findings:
- 4040 interrupt vector is fixed at PC=0x003 (no vector table).
- New 4040 instructions all live at OPR=0000, OPA=0x01..0x0E.
- 4004 DAA (opcode 0xFB) is single-nibble, very different from 8080.
- 4040 STP/STPA/INTA pin names per datasheet (not STOP/STOPACK).
- R16..R23 are not directly named — they're Bank-1 R0..R7 via SB0/SB1.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
- Added tcp_nat.py to handle TCP NAT, implementing the three-way handshake, data flow, and connection state management.
- Introduced udp_nat.py for UDP NAT, managing chip-initiated datagrams and maintaining flow state.
- Created integration tests in test_picow_net_bridge.py to validate the functionality of the TCP and UDP NAT implementations, including ARP, DHCP, ICMP, and DNS interactions.
- Introduced SVG layout dimensions for Phase 1 (B/W mono) and Phase 2 (colour) ePaper panels, detailing active areas, bezels, and pin layouts.
- Developed a phased emulation plan outlining the architecture and deliverables for different panel types, including SSD168x and UC81xx.
- Created a canonical "Hello, World!" sketch for the 1.54" ePaper panel, ensuring compatibility across ESP32, Raspberry Pi Pico, and Arduino Uno.
- Implemented a pure Python SSD168x decoder to validate SPI command sets and framebuffers against specifications.
- Added tests for compiling the hello-world sketch across supported boards and for the SSD168x protocol to ensure correct framebuffer behavior.
- Implemented handshake tests to validate initial bus state and register responses.
- Created end-to-end tests for Pico W LED blinking using MicroPython firmware.
- Added SDPCM framing tests to ensure proper encoding and decoding of control frames.
- Developed IOCTL tests to verify command responses and state changes in the emulator.
- Established a full lifecycle test for WiFi operations, including scanning, connecting, and packet handling.
- Introduced TypeScript configuration for test files to ensure compatibility and strict type checking.
- Implemented `esp32_spi_chip_demo.ino` to demonstrate SPI communication with a 74HC595 shift register.
- Created `esp32_uart_chip_demo.ino` for UART loopback testing with ROT13 transformation.
- Added Python tests for compiling chips and sketches, ensuring valid WASM output and successful compilation for various board families.
- Developed end-to-end tests for ESP32 with custom chips using I2C and SPI, validating synchronous communication through the backend.
- Introduced GPIO bridge tests to verify serial communication and GPIO state changes.
- Ensured all tests validate the expected behavior of the custom chips and their interaction with the ESP32 firmware.
https://github.com/kritishmohapatra/100_Days_100_IoT_Projects
- Introduced `_lib.py` containing shared validators for board support and static source analysis for MicroPython projects.
- Added `conftest.py` to configure pytest for the test suite, simplifying import paths.
- Created `NOT_SUPPORTED.md` files for two projects indicating they cannot be emulated in Velxio due to lack of source code.
- Implemented unit tests for the unsupported projects to verify the presence of the NOT_SUPPORTED marker and source preservation.
Fixes the user-reported bug where two RPi Pico W boards wired GP0↔GP1
running SerialPassthrough don't communicate. Replaces the broken
broadcast-style cross-board logic in addBoard (only routed AVR↔Pi3B,
ignored wires entirely, no RP2040↔anything path) with a wire-aware
Interconnect singleton.
Architecture: digital pin transitions are the lowest-common-denominator
abstraction. Each simulator's hardware peripherals (UART/I2C/SPI) and
bit-banging libraries (SoftwareSerial, software I2C) decode the
transitions naturally — propagate the pin and the protocols come for
free. For cross-process boards (ESP32 backend QEMU, Pi3B QEMU) a
byte-level shortcut is additionally enabled on hardware-UART pin
pairs to handle high-baud links over WebSocket latency.
Implementation:
- New simulation/Interconnect.ts singleton subscribes to wire/board
changes via the Zustand store. Handlers per tier: browser-sim →
pinManager.onPinChange, ESP32 → Esp32Bridge.sendPinEvent, Pi3B →
bridge.sendPinEvent. Re-entrancy guard via per-(board,pin) Set.
- New utils/boardProtocols.ts classifies pins (uart-tx, i2c-sda, etc.)
per board kind, used as optimization hint for the byte shortcut.
- types/wire.ts: added signalType field, exports WireSignalType /
WireColorMap (fixes a pre-existing TS import error in wireColors).
- Deleted the bridgeMap/simulatorMap broadcast forEach blocks in
addBoard. Initial board + future boards register with Interconnect
via setInterconnectRuntime + store subscription.
- PinManager.resetPinStates() helper for test isolation.
Tests (16 new files, 96 tests, all passing):
- Per-pair × per-protocol matrix: dual-arduino-digital,
dual-pico-digital, arduino-pico-digital, triple-pico-digital-chain,
dual-arduino-hw-uart, dual-arduino-software-serial,
arduino-pico-mixed-uart, arduino-esp32-uart, dual-esp32-uart,
pi3-pico-uart, arduino-pico-i2c, arduino-arduino-spi,
interconnect-routing, dual-arduino-multi-protocol (UART+I2C+SPI+
digital + concurrent), dual-pico-multi-protocol (UART0+UART1 alt+
I2C0+I2C1+SPI0+digital + 3-Pico star topology)
- Updated dual-pico-serial-passthrough to assert correct behaviour
- Backend test/multi_board_esp32/test_dual_esp32_serial.py for two
real QEMU instances (skip-graceful when lcgamboa lib absent)
Verified: 1107/1107 tests pass, zero regressions, vite build OK.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
Follows the same pattern as test_esp32_spice_analog.mjs and
test_esp32_spice_ntc_bridge.mjs: compile an ESP32 sketch on-the-fly via
/api/compile/, boot QEMU through the backend WebSocket, and sweep lux
levels while verifying analogRead() returns what ngspice solved.
The netlist uses the exact photodiode cards emitted by
frontend/.../componentToSpice.ts (D_<id> + I_<id>_ph + DPHOTO model), so
any drift in the frontend SPICE mapper surfaces here.
Validated against the live Docker container — lux=0/1000/2500 produce
raw=4095/2854/992, matching the expected 4095/2854/993 within ±1 LSB
and monotonically decreasing with brightness as expected.
The package-lock.json churn is a pre-existing drift: eecircuit-engine
was in package.json but missing from the lock — npm install re-added it.
Companion workflow change (registering the test in backend-e2e-tests.yml)
lives in a separate commit that requires a PAT with workflow scope to push.
- Decoupled electrical simulation from the simulator store, ensuring SPICE is always active for accurate circuit analysis.
- Removed feature flag for electrical simulation, simplifying the state management.
- Preloaded SPICE engine at app start to eliminate latency during the first solve.
- Added comprehensive tests for MOSFET PWM LED behavior and NPN transistor switch functionality, ensuring correct current flow and response to pin states.
- Implemented diagnostics for floating input nodes in RC low-pass filter circuits, addressing singular matrix issues in SPICE simulations.
- Introduced active semiconductor metadata registry for better component management and simulation fidelity.
- Updated Vite configuration to force re-bundling of local wokwi-elements after component additions.
Documents 5 issues found in production logs: RPi3 missing QEMU boot
files (51 hits), ESP32-S3 unsupported machine type, WebSocket race
condition, Google OAuth unhandled 400, and the uvicorn keepalive crash
that was mitigated in 8e3c00e.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Adds frontend/src/data/examples-circuits.ts with 40 new examples organized
into 6 categories, each demonstrating a specific analog/digital/electromech
concept that the SPICE engine can simulate end-to-end:
PASSIVE / ANALOG (10):
voltage-divider, rc-low-pass-filter, wheatstone-bridge,
ntc-temperature, led-current-limiting, parallel-resistors,
pot-adc-reader, photoresistor-light, multi-led-bar,
capacitor-charge-curve
TRANSISTOR / SEMICONDUCTOR (8):
npn-led-switch, pnp-high-side-switch, mosfet-pwm-led,
diode-rectifier, zener-regulator, schottky-reverse-protection,
bjt-common-emitter, darlington-high-current
OP-AMP (5):
opamp-inverting, opamp-voltage-follower, opamp-comparator,
opamp-difference, opamp-schmitt-trigger
LOGIC GATES (6):
and-gate-alarm, xor-toggle-detector, nand-sr-latch,
full-adder, binary-counter-leds, logic-probe
ELECTROMECHANICAL (4):
relay-led-switch, optocoupler-signal,
l293d-motor-control, l293d-speed-pwm
POWER / REGULATOR (3):
power-supply-7805, lm317-adjustable-psu, battery-voltage-monitor
BOARD-SPECIFIC (4):
esp32-dual-adc, mega-multi-led, nano-sensor-station,
esp32-pwm-led-rgb (uses ESP32 LEDC peripheral)
The new examples are appended to exampleProjects[] in examples.ts so the
existing gallery and category filters pick them up automatically.
test/test_circuit/test/spice_examples.test.js validates each example's
analog topology in ngspice — 45 individual assertions covering all 40
examples (plus extra cases for NTC/Zener sweeps and L293D direction).
Sandbox tally: 164 -> 209 tests, 7.9s runtime, all green.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Three new end-to-end tests that combine ESP32 QEMU emulation (via backend
WebSocket) with ngspice-WASM analog circuit solving:
1. test_esp32_spice_analog.mjs — voltage divider sweep
- Compiles a sketch that reads analogRead(34)
- Solves two voltage dividers with ngspice (R1/R2=10k/10k then 10k/30k)
- Injects solved V(mid) into ESP32's ADC via esp32_adc_set
- Verifies Serial output matches within +-50 counts (12-bit ADC)
- Confirms circuit change is detected (different ADC values)
2. test_esp32_spice_ntc_bridge.mjs — Wheatstone bridge temperature sweep
- NTC thermistor in a bridge (0C / 25C / 50C)
- ngspice solves the bridge for each temperature
- ESP32 reads both legs (ADC34+ADC35), computes R_ntc and T via beta model
- Verifies temperature within +-5C tolerance across sweep
3. test_esp32_spice_smoke.mjs — ngspice-only smoke test (no backend needed)
Also adds eecircuit-engine to test/backend/e2e/package.json.
Prerequisites: backend on localhost:8001 with esp32 core installed.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Adds 44 SPICE mappers, 58 custom metadata entries, and 12 visual
Web Components covering logic gates, transistors, op-amps, regulators,
sources, electromechanical parts and integrated-circuit packaging.
Fase 9 — component catalog expansion
------------------------------------
- 7 logic gates (AND/OR/NAND/NOR/XOR/XNOR + NOT) as SPICE B-sources
- 8 multi-input gates (AND/OR/NAND/NOR with 3 and 4 inputs)
- 9 transistors: 5 BJTs (incl. PNP 2N3906/BC557) + 4 MOSFETs (incl.
P-channel IRF9540/FQP27P06). NMOS refactored from Level=3 W=0.1
(hangs ngspice) to Level=1 with sane W/L
- 5 op-amps: LM358, LM741, TL072, LM324 with per-chip saturation
rails + opamp-ideal
- 4 linear regulators (7805, 7812, 7905, LM317) with dropout
- 3 batteries (9V, AA, coin-cell) with realistic ESR
- Signal generator (sine / square / DC)
- 2 Schottky diodes (1N5817, 1N5819) + photodiode (lux-driven
current source)
Fase 10 — electromechanical + ICs
---------------------------------
- Relay (SPDT): coil + L + S-switch with native hysteresis +
flyback diode, inverted-control trick for the NC contact
- Optocouplers 4N25 and PC817 (LED + CCCS with CTR=0.5 / 1.0)
- 7 74HC ICs as DIP-14 packages emitting 4 or 6 B-sources per
component (first mapper pattern emitting multiple device cards)
- 3 flip-flops (D, T, JK) — digital-sim only (edge detection is
not representable in ngspice .op)
- L293D dual H-bridge motor driver
Infrastructure
--------------
- scripts/component-overrides.json gains a _customComponents[] array
that lets new Velxio-only parts survive metadata regeneration
(previously applyOverrides() could only patch wokwi-elements
components that had already been scanned)
- scripts/generate-component-metadata.ts injects custom entries
before the patch loop
- New ComponentCategory values: 'logic', 'analog', 'electromech'
- frontend/src/components/DynamicComponent.tsx PASSIVE tracing
extended from just ['resistor','resistor-us'] to 9 two-terminal
passives with per-part pin name maps
- New CI workflow test-circuit.yml runs the sandbox on push/PR
- frontend-tests.yml regenerates metadata and fails if committed
JSON is stale
- Documented 2 new ngspice gotchas in circuit-emulation-gotchas.md:
unicode in netlist titles silently hangs the parser, and
MOSFET Level=3 + W=0.1m causes .op to hang
- 164/164 sandbox tests passing in ~9 s (was 88 pre-fase-9)
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
- Implemented a comprehensive test script (test_micropython_pico.mjs) that performs the following:
- Part 1: Checks backend compilation of a simple Arduino sketch for the rp2040:rp2040:rpipico board.
- Part 2: Downloads MicroPython v1.20.0 UF2 firmware and loads it into a rp2040js simulator.
- Part 3: Simulates the Pico, verifies REPL output, and checks execution of injected Python code.
- Includes detailed logging and error handling for each step of the process.
refactor: Update wiring examples for E32 OLED integration; correct pin mappings for VCC, GND, DATA, and CLK
test: Improve unit tests for ESPIDFCompiler; add scenarios for library resolution and CMake patching
chore: Mark subproject commits as dirty for wokwi-libs
- Implement tests for BMP280, DS1307, DS3231, I2CWriteSink, and MPU6050 slaves in test_i2c_slaves.py.
- Create test suite for Velxio MCP server tools in test_mcp_tools.py, covering Wokwi utilities and circuit management functions.
- Add tests for parsing WiFi and BLE serial output in test_wifi_status_parser.py, ensuring correct status events are captured.
- Updated the threshold for switching to data mode in MPU6050Slave from 2 to 3 WHO_AM_I reads to ensure correct chip identification.
- Enhanced comments in the code to clarify the sequence of I2C events during initialization.
- Added a new test file `test_mpu6050_emulation.py` to validate the MPU6050Slave state machine and ensure it handles the full Adafruit_MPU6050::begin() event sequence correctly.
- Updated existing tests to reflect the changes in the I2C handling logic.
- Modified `components-metadata.json` to update the generated timestamp.
- Marked submodules `rp2040js` and `wokwi-elements` as dirty to reflect local changes.
- Created a new DocsPage component for project documentation with links to GitHub and Discord.
- Added Arduino sketch for serial communication test between Raspberry Pi and Arduino.
- Implemented avr_runner.js to emulate ATmega328P and bridge serial communication over TCP.
- Developed a Python test script to validate the serial integration between the emulated Raspberry Pi and Arduino.
David Montero