The ESP-IDF compile path stages exactly the libraries declared in the
example (no transitive resolution), so Adafruit_GFX.h failing to find
Adafruit_I2CDevice.h broke esp32s3-ili9341-hello and esp32-oled-4pin-i2c
with 'Compilation produced no firmware'. The other ESP32 GFX examples
(esp32-oled, esp32-bmp280) already declare BusIO explicitly.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
A part can land in the store at its FINAL position before its element
mounts: the agent streams add_component and the seating move in one batch,
and updateComponent's reseat then finds no DOM (computeSeating null) and
keeps the empty seating. Nothing re-derived it afterwards — the agent-side
seat correction skips when the position needs no nudge, and 'pininfo-change'
only fires on pin-SET swaps, not on plain init. Meanwhile run_simulation
executes right after the SSE round, before the correction's animation frame.
Net effect, reported by a user as a suspicion that turned out exactly right:
a clock the agent built and ran in one turn showed a dead display, while
reloading the project and running it worked — bb seating wires are persisted,
so on reload they exist before Run is pressed.
DynamicComponent now reseats once the element's pinInfo first becomes
measurable (same polling cadence as the pinInfo-ready effect), which closes
the hole for every path that stores a final position before mount: agent
batches, project load, undo. To keep that free on load,
reseatComponentOnBreadboard skips the store write when there is nothing
seated and nothing to clear — otherwise every off-board part would churn the
wires array identity once per mount.
Verified live end-to-end: agent adds + seats + wires + compiles + RUNS in a
single turn; the seated LED blinks immediately (4 transitions sampled), with
all 4 seated-pin markers present — no reload needed.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Seating is otherwise invisible — a seated pin connects to its hole through a
zero-length `bb` wire that never renders — so a user couldn't tell a part
that merely sits ON the board from one whose pins are actually connected.
This was reported after placing parts that looked seated but gave no signal
they were wired in.
SeatedPinMarkers draws a small always-on green dot (Wokwi-style) on each pin
that has a `bb` wire, derived once per render from the store's wires
(component pin = wire start). Non-interactive layer below the wire-target
hit boxes; only breadboard-seated pins light up, so board-wired builtins stay
unmarked — exactly the "seated vs connected" distinction that was missing.
The per-pin rotation math (rotate about the wrapper centre, which the overlay
layers live outside of) is extracted from PinOverlay into a shared
`rotatePinLocal`, so the dots and the wire-target boxes can never drift apart
under rotation. A test asserts rotatePinLocal agrees with calculatePinPosition
at 0/90/180/270°.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The agent computes exact hole assignments server-side but can only send an
approximate canvas x/y, because the rotation pivot is the DOM wrapper centre
and the wrapper includes a text label the server cannot measure. Under
rotation that left seated parts off by up to ~4 px — enough that a diode
(pins 7.5 pitches apart) half-seated: computeSeating found no hole for the
far pin and it went electrically dead.
resolveSeatPosition corrects it in the browser by pure translation: read
where the anchor pin actually is from live DOM geometry (real pivot), read
where the solver put it, shift the whole part by the difference. Every other
pin follows because pin-to-pin offsets are pivot-free. It never re-solves, so
it cannot slide the part to different holes and the validated netlist holds.
The anchor target is the solver's anchor position in breadboard-element
space, WITH its sub-pitch centroid translation — not the hole centre.
Targeting the centre would re-break the diode (far pin 4.8 px out). Verified
against real rendered geometry in a browser: resistor and diode at 90° both
seat within the intrinsic lattice residual (0.6 / 2.4 px).
Applied via a `seat` payload on the move_component effect (velxio-prod
overlay); this commit is the resolver + tests.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Three changes, all driven by a real project where a 4-digit 7-segment clock
was unreadable and half its parts were not actually seated.
Labels on hover only
--------------------
Eight vertical resistors at 19 px pitch rendered eight 93 px "Resistor 220 Ω"
labels on top of each other, hiding the parts and the breadboard holes; the
SPICE overlay added ~40 more `0uV` pills. Both are now revealed on hover:
hovering a part also lights up the voltages of every wire touching it.
The label is hidden with OPACITY and stays in flow. pinPositionCalculator
derives the rotation pivot from wrapper.offsetHeight, so taking it out of
flow would move the pins of every rotated component in every saved project.
Seat-on-drop
------------
The drag-time magnet only aligned the anchor pin and assumed the rest
followed, which is how parts ended up HALF-seated: some pins in holes, the
rest dead in the air. It looks mounted in a screenshot and silently breaks
the circuit. On release we now re-solve properly — nearest position where
EVERY pin is in a free hole, sliding past occupied columns — via the new
solvePlacement/seatOnDrop. Geometry comes from the element's own pinInfo,
so there is no part whitelist.
Sub-pitch translation
---------------------
solvePlacement first assigned pins to holes at half-pitch, then translates
by the centroid of the residuals before judging fit. Pinning the anchor dead
centre refused every off-lattice footprint: a diode spans 7.5 pitches, so
one leg landed 4.8 px out. Shifted 2.4 px, BOTH legs sit inside tolerance —
what bending the leads does on a real board. Measured over the catalog this
takes seatable parts from 87 to 125 of 152; diodes, transistors, regulators,
optocouplers and flip-flops are rescued with no artwork change.
Staying under SEAT_TOLERANCE (< half pitch) keeps each pin's nearest hole
unambiguous, so computeSeating resolves the same holes and the netlist is
unaffected by the small offset.
Also: refuse a placement that would put two of a part's own pins in one
strip. A column strip — and far worse, a power rail — is a single net, so
such a seating shorts the part to itself. Without it a 7-segment happily
lays its pins across a rail. And deduplicate pin names before solving:
calculatePinPosition resolves by name and returns the first match, so a
board carrying GND x5 collided with itself and was refused outright.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Root cause of the 'digits=4 display seated with the 1-digit COM pinout'
bug: property values arrive as STRINGS (agent set_component_property,
the property dialog's text inputs) and were assigned to the web
component verbatim — wokwi's 7segment does switch(this.digits) with
numeric cases, so el.digits='4' silently fell back to the 1-digit
pinout (and 'false' stayed truthy for boolean props like colon).
- DynamicComponent now coerces string values to the TYPE of the
metadata default for that key (number/boolean) before assigning.
- New pininfo-change listener: when a property swaps the element's pin
set (digits, flip, pins edge), the elements announce it — re-derive
the breadboard seating then, with the fresh pinout, instead of never.
Every resistor variant ('resistor' + 'resistor-<value>') now lands on
the canvas rotated 90 degrees: reads better, takes less horizontal
space, and drops straight into breadboard columns. Explicit rotations
in metadata defaults are respected. The breadboard auto-vertical drag
check widens from the two-entry set to the same prefix predicate, so
preconfigured variants (resistor-330 etc.) rotate on the board too.
Parts now plug INTO the breadboard instead of using it as a junction box:
- Drag magnetism: while dragging, the part's anchor pin snaps to the
nearest hole center (9 px range, 9.6 px grid) so parts land perfectly
aligned, like Wokwi.
- Seating: every pin within 4 px of a hole gets an invisible zero-length
wire (Wire.bb) from pin to hole — the exact model Wokwi persists as
["r1:1","bb1:6t.b","",["$bb"]]. Electrically they are ordinary
wires, so the netlist builder, digital trace and SPICE need zero
changes; they are simply not rendered and not hit-testable. Seating
re-computes on every move/rotation (updateComponent), and moving the
breadboard carries its seated parts along.
- Resistors auto-rotate to vertical when dragged over a breadboard
(their 58.8 px pin span bridges the center trench rows b-f exactly).
- Seat tolerance 4 px: absorbs the worst element pin-spacing residual
(~1.6 px) while staying under half the hole pitch, so a pin is never
ambiguous between holes.
Wokwi interchange fixes that fell out of the diagram.json research:
- import maps the top-level rotate attr onto properties.rotation
(previously every rotated part imported flat) and export emits it
back as rotate instead of leaking it into attrs;
- $bb / empty-color connections import as bb seating wires and export
back as ["$bb"] entries, so parts-on-breadboard projects round-trip;
- wokwi-breadboard-half aliases to the full breadboard (hole names are
a strict superset, so every connection stays valid).
Breadboard elements now export their pure hole grids and import cleanly
without a DOM (node tests); geometry + store seating covered by
breadboard-snap.test.ts and breadboard-seating.test.ts.
Three stale-project-identity fixes from reviewing the New-workspace flow:
- New workspace (web): handleNewClick cleared the workspace and the
current project but left the browser on the old /user/slug URL — a
refresh (or back-button pop) silently reloaded the OLD project over
the fresh unsaved workspace. Now replaceState's to the localized
/editor (replace, not push, so no back-entry points at the stale
project route).
- New workspace (desktop menu): same URL fix for the newProject menu
action, which cleared identity but never left the project route.
- .vlx import: importVlxFile mutated the stores WITHOUT clearing
currentProject — with a saved project open, autosave saw the
imported content as dirty edits on the old projectId and silently
PUT the .vlx contents over the user's saved project (and pushed the
clobber to GitHub on linked projects). Now severs identity first,
same guard loadExample.ts already documents.
verifyCircuitFromStore() builds the worst-case snapshot (every wired
digital pin driven HIGH) and solves it — extracted verbatim from
EditorToolbar's runVerification so programmatic runners (editor
extensions, agents) can gate their own run paths on the same rules.
No behavior change for the Run button.
Creating a wire with a direct pin-to-pin click (no user waypoints) now
routes around other components' bounding boxes instead of crossing
them. Routing happens exactly once, at creation: the routed corners are
stored as ordinary waypoints, so every later manual edit stays where
the user puts it — never re-routed.
Router (utils/wireAutoRoute.ts):
- tries the preview elbow first (clear -> keep existing behavior and
the WYSIWYG shape), then the opposite elbow, then A* over the
compressed grid spanned by pin coordinates and obstacle edges
inflated by an 8 px clearance, with a 40 px per-bend penalty so
straighter routes win
- obstacles are component boxes only (never boards — pins sit on both
board edges and detouring around a board produces absurd routes),
excluding the wire's own endpoint components, measured from the
rendered DOM; rects containing an endpoint are dropped
- any failure (walled-off target, oversized grid, no DOM) falls back
to the previous direct-elbow behavior
Hand-aligning a dragged segment could leave two parallel runs a pixel
or two apart, joined by a tiny perpendicular step, because alignment
snapping only ever targeted OTHER wires' geometry.
- Segment and bend-point drags now also snap (6 px threshold) against
the dragged wire's own points — excluding the ones being dragged —
so a run clicks into line with its neighbour and the exact
simplification fuses them into one segment on commit.
- fuseMicroJogs: parallel runs offset by under 2 px joined by a tiny
step are aligned automatically (the run not anchored to a wire
endpoint moves; shorter run yields when both are free). Applied at
render time and in renderedToWaypoints/normalizeWireWaypoints, so
already-saved crooked wires display straight without touching data.
Three wiring quality fixes:
- Rounded corners: every bend now renders as a quadratic curve
(radius 7, clamped to half the shorter adjacent segment), with
round line caps/joins. Segment/waypoint drag previews and the
in-progress preview use the same path builder so the look is
consistent everywhere.
- Degenerate geometry cleanup at render time: the expanded polyline
is simplified (duplicates, collinear runs, U-turns) before the
path is emitted, so wires saved with junk waypoints no longer
render on top of themselves. Stored data is untouched until the
user edits the wire.
- WYSIWYG commit: finishWireCreation materialises the final-leg
elbow exactly as the live preview drew it (longer axis first) and
normalises the stored waypoints. Previously the committed wire
fell back to horizontal-first and visibly changed shape on click.
simplifyOrthogonalPath moved to wireUtils (re-exported from
wireHitDetection for existing imports); the duplicated inline
expansions in SimulatorCanvas now use the shared helper. Waypoint
dots on idle wires removed (visual noise); endpoint dots stay.
Monaco's focus sink is a plain div (.native-edit-context under the
EditContext API), neither an input tag nor contentEditable, so the
typing guard missed it and a mapped letter typed into the code editor
pressed the button. Treat any keydown originating inside .monaco-editor
as typing.
Any pushbutton (pushbutton / pushbutton-6mm) can now be driven from the
keyboard. Assign a key from the component property dialog — a keycap
control captures the next keypress (Escape cancels, modifiers alone are
rejected) — and a keycap badge next to the component label shows the
mapping on the canvas. Several buttons may share one key on purpose;
the dialog shows a hint when that happens.
At runtime a global bridge translates keydown/keyup into the same
button-press / button-release DOM events the mouse fires on the wokwi
element, so every simulation path (avr8js pin logic, SPICE-driven
inputs, the QEMU GPIO bridge, the pressed visual) behaves identically
to a mouse click. Guards: ignored while typing in inputs or the code
editor, ignored with Ctrl/Alt/Meta held, auto-repeat collapses into one
long press, and window blur releases everything so no button sticks
after Alt-Tab.
The binding is stored as the component's 'key' property, so it
round-trips through project saves and .vlx exports and is undoable like
any other property edit. Strings added to all 9 locales.
Convert the remaining window.confirm() call sites to the in-app
MessageDialogHost, extended with a new confirm mode (Cancel + Confirm
buttons, optional danger styling) via showConfirmDialog().
Sites converted:
- New workspace (EditorPage)
- Load project / delete file (FileExplorer)
- Overwrite SPIFFS file (BoardOptionsModal)
- Delete VFS node (VirtualFileSystem)
All dialog strings are internationalized across the 9 supported locales
(en, es, pt-br, it, fr, zh-cn, de, ja, ru); the two previously
English-only modals now pull from i18n too.
A breadboard is the physical base of a circuit — boards, components and
wires all plug into it — so it should never cover them. Pin its group at
z-index -1 (below boards z 0, components z 1/2, wires z 35), ignoring
selection. Detected by metadataId prefix 'breadboard' (breadboard,
breadboard-mini). Its own pins stay wireable wherever it's not covered.
The dense-component threshold (>60 pins) meant boards like the Arduino
(31 pins) still painted every pin blue on hover — a wall of squares. Drop
the threshold: every component/board now keeps its squares invisible and
lights up only the ONE under the cursor (matching the breadboard, which
users already liked). Wiring mode still paints them all — all valid targets.
Removing isActive from board showPins (prev commit) exposed a latent bug:
BoardOnCanvas put onMouseEnter/onMouseLeave on the drag overlay, a SIBLING
of PinOverlay. Moving the cursor from the overlay onto a pin square fired
the overlay's mouseleave, cleared hoveredBoardId, and hid every pin right
as you reached one — so a board pin could never be clicked to start a wire
(breadboards were fine: their group wrapper owns both body and pins).
Move the hover handlers to the wrapper div that contains the board body,
the drag overlay AND the pin squares, so moving among them never fires
mouseleave. Board dragging (onMouseDown on the overlay) is unaffected.
Three UX fixes to the pin squares:
- Pins show on hover or while wiring only. The active board and the
selected component used to light every pin permanently.
- Dense components (>60 pins — breadboards) don't paint a wall of blue
on hover: squares stay invisible and light up individually under the
cursor. While a wire is in progress every square paints again since
they're all valid targets (new `wiring` prop threaded to PinOverlay).
- mousedown on a pin square stops propagation, so press-and-drag from a
pin no longer pans the canvas.
Two stacking bugs:
1. Pin overlays used a global z-index 30 while component bodies sit at
z 0-5, all in .canvas-world's single stacking context — so a covered
component's pins painted on top of whatever covered it (arduino pins
showing through a breadboard). Each component/board group is now a
zero-size positioned wrapper that forms its own stacking context
(boards z 0, components z 1, selected z 2): pins stay above their own
body but are hidden together with it. .components-area becomes
pointer-events: none so board pins/drag overlays (now trapped at z 0)
keep receiving clicks through it; component groups re-enable their own.
2. The Add Component / board picker overlays (z 1000/2000) rendered
behind the pro AI chat panel (z 8000). Both now portal to <body> at
z 9000.
Verified in-app: board drag, component drag, wire creation from board
pin to LED, covered pins hidden (0/14 leak), covering component's pins
still clickable.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The Sign-in links navigate with a full page load (they mount in a
separate React root without Router context), which wipes the in-memory
Zustand workspace. New utils/workspaceDraft stashes the whole workspace
(reusing the lossless .vlx serialisation) to sessionStorage before that
navigation and restores it once when the editor remounts after login —
so a user who was building a circuit and signs in lands back on their
work instead of the empty starter board.
Strictly scoped to the login round-trip by a one-shot restore flag (not
a general autosave), and skipped when a named project is already loaded
so it never clobbers one. EditorPage calls restoreStashedWorkspace() on
mount; the pro overlay's auth links call stashWorkspaceForAuth() before
navigating.
useMessageDialogStore + <MessageDialogHost /> (mounted once in App.tsx)
give a themed in-app dialog callable from anywhere — React components
and plain .ts modules alike via showMessageDialog(msg, {kind}). Swaps
the native alert() calls in FileExplorer (import errors) and the
desktop menu (.vlx open errors, updater status) for it; the pro overlay
can reuse the same store.
The 'Create with AI' button referenced the Pro AI agent (hardcoded
prompt, agent event) inside the anonymous OSS dialog — chat/agent logic
must live in the velxio-prod overlay, not here. CustomChipDialog now
just exposes a generic `data-velxio-slot="custom-chip-actions"`
extension point (empty in OSS) and hangs its close handler on the slot
element so the overlay can dismiss the dialog after acting. The button
itself, its prompt and the Pro entitlement gate move to the overlay.
- 'Create with AI' button in CustomChipDialog dispatches the generic
velxio:agent-prompt window event (no-op without a listener — the pro
overlay's chat panel picks it up and prefills the composer).
- chipCompileService maps the hosted deployment's 401 gate to a human
'sign in to compile custom chips' message instead of a raw status
line. Self-hosted OSS keeps the route open and never sees either.
Registers upstream @wokwi/elements, velxio-elements/ and the element
classes living next to their React wrappers in velxio-components/ —
without pulling any React component graph. Used by pin-metadata
introspection in tests/generators (the pro agent's metadata export).
Google's auto-generated sitelinks for "velxio" surfaced docs/blog pages
but not the Editor (the primary app) or Home. Sitelinks can't be forced,
but an explicit SiteNavigationElement ItemList naming the primary nav —
Editor, Examples, Documentation, Pricing, About, in that order — is the
recognized structured-data hint for what the site's main sections are.
The examples page showed only ~3 cards per row (the grid was capped at
max-width 1200px with minmax(300px) columns), a tall header, and three
stacked filter rows (16 board tabs + category + difficulty) that pushed
the actual examples far down the page. Card thumbnails also letterboxed
with black bars on the sides.
- Grid: widen to 1680px + minmax(232px) columns → ~6 cols on a 1600px
screen (was 3). Cards smaller/denser (radius, info padding, title).
- Thumbnails: fixed 5:3 aspect-ratio container + object-fit:cover so the
preview fills edge to edge — no more black side bars.
- Filters: replace the search row + 16 board tabs + two button rows with
ONE compact toolbar (search + Board/Category/Difficulty dropdowns +
live count) and removable filter chips (badges with ×) + Clear all.
- Header trimmed (smaller title, less margin) so cards start high.
The red viewport rectangle read the React `pan` prop, but the canvas
pans by mutating panRef + the .canvas-world transform directly (no
setState until pointer-up, for zero-lag dragging). So while you dragged
the canvas the rectangle sat frozen and only jumped at the end. The
minimap now also receives panRef/zoomRef and mirrors them via a
requestAnimationFrame loop that setStates only on change, so the rect
follows the canvas every frame while keeping the canvas render-free
during the gesture.
Also: boards were all drawn as one fixed 120x90 world rectangle
regardless of the actual board, misrepresenting the layout. Use the real
per-board BOARD_SIZE (now exported from BoardOnCanvas) so each footprint
is proportional. And enlarge the map 100x75 -> 160x120 (same 4:3 as the
4000x3000 world) so it's usable.
The profile Duplicate dialog passes the chosen name, description and
visibility to POST /projects/{id}/duplicate. Options are optional — an
empty call still clones with the source name + " (copy)".
Pairs with the pro-overlay endpoint that clones a project (row + file
groups) into the caller's account. Lives next to deleteProject — the
OSS client already fronts the pro-only projects API when overlaid.
New optional `featured` metadata flag: ComponentRegistry stable-sorts
featured components to the front after loading (and indexes categories
from the sorted list, so per-category views keep the same order). The
two breadboards are marked featured in component-overrides.json — they
are everyday parts and now open the component grid instead of sitting
at the bottom below every diode.
Swap the programmatic SVGs for the real Fritzing breadboard art
(breadboard2.svg / miniBreadboard.svg from fritzing/fritzing-parts),
served from /component-svgs/fritzing/ and scaled x4/3 so the hole pitch
is the wokwi-standard 9.6 CSS px. pinInfo is computed from the measured
Fritzing hole grid (terminal col 1 at x=10.92, rails at x=25.33 in
5-hole groups; wokwi rows a-e map onto fritzing J..F on the full board,
1:1 on the mini; the red stripe marks the + row of each rail pair), so
wire endpoints land exactly on the drawn holes. The element reserves its
final size immediately and falls back to a light programmatic SVG with
identical geometry if the asset can't load. ATTRIBUTION.md records the
CC-BY-SA 3.0 license of the two SVG files.
Verified in the app: fritzing art renders for both boards, the LED
circuit through full-board column + mini column + ground rail still
lights, SPICE overlay shows the merged nets (5.00V on the pin-8 net).
Two velxio-native passive parts, rendered as web components with
programmatic SVG + precomputed pinInfo (velxio-breadboard 830 holes,
velxio-breadboard-mini 170). Pin names follow the Wokwi convention
(holes `18t.d` / `17b.i`, rails `tp/tn/bp/bn.N`) and the metadata ids
are `breadboard` / `breadboard-mini`, so wokwi diagram.json zips
import/export with no aliasing.
Internal connectivity (5-hole column strips, full-length power rails)
is centralized in utils/breadboardNets.ts and wired into every net
consumer:
- NetlistBuilder: unionBreadboardGroups joins wired holes per group at
the union-find level in buildNetlist, buildWireNetMap and
buildBoardPinNetMap — SPICE, the circuit verifier and the voltage
overlay all see one net per strip/rail with no extra cards.
- DynamicComponent.traceDetailed: the digital trace hops through every
other wired hole of the entered group, so parts wired through a
breadboard still resolve their board pin (2-terminal
PASSIVE_PIN_PAIRS could not express N-hole groups).
Verified end-to-end in the app: Uno pin 8 -> full-board column ->
resistor -> mini-board column -> LED -> ground rail -> GND lights the
LED, and the HUD shows the 3 collapsed SPICE nets. 8 new unit tests
(breadboard-nets.test.ts); netlist-builder + circuit-verifier suites
stay green.
Hardware-SPI (FSPI/GPSPI2) ILI9341 draw from an ESP32-S3: fill + rounded
rect + text via Adafruit_GFX/ILI9341. Exercises the S3 GPSPI2 controller
end to end (worker SPI stream + DC/CS/RST -> the canvas TFT decoder).
When addBoard promotes a board to active (first board, or the previously
active one was removed) it set activeBoardId without syncing s.simulator,
unlike setActiveBoardId which sets both. Parts that read s.simulator - SPI
displays (ILI9341) attach spi.onByte to the active simulator - then wired
onto the previous board's bus and never received data, so a boards[] ESP32
example with a TFT rendered black. Sync simulator to the promoted board
(no-op when the active board is unchanged).
Adds `velxio-ssd1306-i2c-4pin`, a native 4-pin SSD1306 OLED module
(GND/VCC/SCL/SDA) — the cheap 0.96" I2C board most beginners actually have,
matching Wokwi's board-ssd1306. The 8-pin `wokwi-ssd1306` breakout stays; this
is the distinct 4-pin part (issue #215). Same SSD1306Core render pipeline
(imageData/redraw) so the display paints identically; I2C-only, address via the
i2cAddress property (default 0x3C). Styled after the existing 8-pin element
(blue PCB, dark screen, corner holes, star).
Ships four "SSD1306 OLED (4-pin I2C)" gallery examples wiring it over I2C on
Arduino Uno (A4/A5), ESP32 (21/22), Raspberry Pi Pico (GP4/GP5) and STM32 Blue
Pill (PB7/PB6).
English is the default locale and is served at the root with no prefix, so
/en/project/x (a natural guess by analogy with /es/, /zh-cn/, ...) matched no
route and rendered blank. Redirect /en/* -> /* (and /en -> /), preserving query
and hash, so those URLs land on the right page while the canonical prefix-free
English URLs stay put for SEO. The other 8 locales already work under their
/<locale>/ prefixes.
Follow-up to the SSD1306 picker consolidation. All 68 saved projects that used
the retired ssd1306-i2c / ssd1306-spi ids have been migrated to the single
`ssd1306` (metadataId rewritten, protocol pinned), so the simulation aliases
are no longer needed and are removed.
- Auto-detect refined to CS-only: chip-select is the SPI-exclusive signal;
DC does NOT imply SPI (on the 8-pin module DC doubles as the I2C address /
SA0 line, so many I2C circuits wire it). Fixes false-SPI on those circuits.
- The `ssd1306` part honors an explicit `protocol` property when present
(migrated legacy projects carry it) and auto-detects otherwise.
- loadProjectState normalizes any lingering ssd1306-i2c/spi ids (old .vlx
files, pre-migration snapshots) to `ssd1306` + the matching protocol, so
removing the aliases can never blank an old import.
The SSD1306 was three picker entries — a generic `ssd1306` with a protocol
selector plus `ssd1306-i2c` / `ssd1306-spi` shortcuts (issue #101) — all the
same 8-pin wokwi-ssd1306 element. That is confusing for one physical module
(issue #215). Wokwi ships a single I2C-only part; this goes one better: a
single part that auto-detects the protocol from the wiring, like a real
breadboard — CS or DC wired to a GPIO means SPI, otherwise I2C. No protocol
switch to set, just wire it up.
Works on every board with an I2C/SPI bus (AVR, RP2040, ESP32 Xtensa, STM32).
The ssd1306-i2c / ssd1306-spi ids stay as backward-compat simulation aliases
for projects saved before the merge, but are removed from the picker. Adds an
i2cAddress property (0x3c/0x3d) matching the real module and Wokwi.
Note: ESP32-C3, Raspberry Pi 3 and the bare RISC-V board do not emulate I2C/SPI
peripherals, so no I2C/SPI device (this or any other) attaches there yet.
Esp32C3Simulator already had the GPIO_IN plumbing (setPinState -> gpioIn ->
GPIO_IN_REG read) but never opted into connectDigitalInputsToMcu, so a pin
wired to a switch/button was never fed the solved circuit voltage and
digitalRead() ignored the real wiring. Enabling the flag (as AVRSimulator and
RP2040Simulator already do) completes the issue #247 fix: the ESP32-C3 now
reads GPIO2 from the SPICE solve, so toggling the slide switch flips the LED.
BasicParts' button/slide-switch seed already yields to spiceDriven(), so there
is no double-drive.
The slide-switch SPICE model only wired pin 1 <-> pin 2 (an SPST), ignoring
pin 3. The part is really an SPDT whose common wiper (pin 2) selects pin 1 at
value=0 or pin 3 at value=1, so a switch wired GND-1 / signal-2 / VCC-3 (the
natural Wokwi hookup) could never pull its signal high. Fixes the reported
ESP32-C3 case (issue #247) where only the green LED lit and the switch never
toggled the red one.
Second cause on that board: the ESP32-C3-DevKitM-1 exposes its supply as
3V3.1/3V3.2 and 5V.1/5V.2 (there is no bare 3V3/5V pin). VCC_PIN_RE has no
numeric-suffix branch on purpose (a dual-supply pin such as L293D VCC2 must
not collapse onto the shared logic rail), so those numbered pins floated at
0 V and the switch's HIGH side was dead. List them in boardPinGroups for
esp32-c3 / esp32-s3 / esp32-cam.
- componentToSpice: SPDT emission (both throws, complementary 0.01/1e9 R).
- digitalGateEngine: both driveSwitch paths (all-digital + mixed) made SPDT to
match, so the pure-digital paint and the ngspice solve agree.
- examples-digital / examples-circuits: rewire every slide-switch so the rail
feeds pin 3 and pin 1 is the value=0 throw, preserving value=ON=HIGH.
- spice-slide-switch-spdt-repro test reproduces issue #247 at the netlist level.
The top bar packs three zones onto one row: the view-mode toggle, the editor
actions (Compile/Run/Stop/...), and the canvas controls (board selector,
Serial, Scope, zoom, Add) portaled in from SimulatorCanvas. The editor zone
was flex:1 min-width:0 while the canvas zone was fixed-width, so when the bar
narrowed - mainly when the right-docked AI chat opens - the editor zone shrank
below its own buttons and painted them over the board selector / Serial /
Scope. The existing collapse logic was keyed to the viewport (@media 768px),
so it never fired on a wide screen with the chat open.
Make the shared bar a container-query context and collapse every zone by the
bar's own width instead of the viewport: view-mode labels drop to icons first,
then Serial/Scope/Add labels and the board selector ellipsizes, then the
component count and finally the zoom buttons (wheel-zoom still works). Floor
the editor zone at its collapsed content width so it can never underflow and
overlap; past that the lower-priority canvas controls yield toward the right
edge instead. Verified across bar widths 660-1140px with the AI chat open:
overlap eliminated, dropdown menus still render un-clipped.
The file-tabs strip in the toolbar center duplicated affordances that
already exist elsewhere: the file it showed is selected in the left file
explorer, and its board-owner label duplicated the board selector combo.
It also ate horizontal space and crowded the action row on narrow panes.
Remove the FileTabs component entirely; the left explorer is now the single
place to switch files. The toolbar center slot stays as an empty flex
spacer so the right action group remains pinned to the far right.
In a multi-board project the wired boards are one system, so running just
the active board almost never matches intent (a cross-wired UART pair only
comes alive when both run). The primary Run button now runs ALL boards when
there is more than one, with a split caret-menu to still run only the active
board. Single-board and board-less behaviour is unchanged, and the separate
Run-All double-triangle button is kept only for board+chip / chips-only
projects where the primary Run is not already a run-all.
The esp32-blink-led example wired the external red LED straight from GPIO4
to the anode with no current-limiting resistor. Add a 220 Ohm resistor in
series (GPIO4 -> R -> LED anode -> GND) so the example models correct
practice and matches the other LED examples.
WebSocket-backed boards (ESP32, STM32, Raspberry Pi) reach the electrical
simulation only through PinManager.triggerPinChange, which updated the pin
state + notified listeners but never requested an electrical re-solve. AVR
and RP2040 already resolve at their own toggle sites. As a result an analog
part on an MCU-driven net (e.g. a resistor-less LED whose brightness comes
from the SPICE solve) stayed at its first solved value until unrelated
activity (such as serial output) forced a solve — so an ESP32 blink with no
Serial in loop() left the LED stuck on.
Request an electrical re-solve after an 'mcu'-sourced pin edge, in one place
(triggerPinChange), covering all WS boards. Gated to source==='mcu' so the
solver's own input feedback (triggerPinChange with the default 'external'
source) can't loop; requestElectricalResolve coalesces overlapping ticks so
a per-edge call is cheap.
After deleting the default board and adding a different one via the canvas
picker, the editor kept editing the removed board's (now deleted) file group
while compile read the NEW board's default group — so code typed into the
editor was silently dropped and the board ran its default sketch ("compiles
fine but runs the old code"). addBoard now points the editor at the new
board's group when it becomes active, and removeBoard re-points it at whatever
board is active afterwards. setActiveBoardId already did this; the canvas
picker calls addBoard directly. Adds a regression test.
Extend the spice-driven input path (already live for AVR/ESP32) to RP2040 and
STM32 so digitalRead() of an INPUT pin reflects the actual wiring: a pin tied
to a rail reads that rail, and an INPUT_PULLUP button-to-GND reads idle-HIGH /
pressed-LOW instead of floating or inverted.
RP2040 (rp2040js, frontend-only): the GPIO listener now splits input vs output
mode. Input pins report their pad pull (InputPullUp/Down) via setPinPull and
seed the pull's idle level (rp2040js does not auto-apply the pad pull to the
readable input register); the SPICE solve then overrides via connectDigital-
InputsToMcu when the net is actually sourced. Output pins drive as before.
spiceDrivenInputs = true.
STM32 (backend QEMU): the worker now forwards a new gpio_pull event (from the
libqemu-arm picsimlab_pull_pin callback) so the netlist stamps the matching
weak resistor; Stm32Bridge surfaces it, Stm32BridgeShim opts into
spiceDrivenInputs, and collectPinStates maps PA0/PC13 names to the linear pin
so the pull is read. STM32 outputs stay on the part layer (unchanged).
Event-driven parts with no SPICE model (rotary encoder, keypad) remain
protected by the existing sourcedNets gate in the connector.
Re-do the AVR spice-driven digital inputs (reverted in c11c195) the right way so
INPUT_PULLUP buttons keep working. PinManager.updatePort now detects the AVR
internal pull-up (input DDR bit + PORT bit high) and sets the pin pull, so the
netlist stamps the 45k pull-up and an INPUT_PULLUP input reads HIGH at idle.
connectDigitalInputsToMcu drives a pin from the solve only when its net is
source-backed by a RAIL or a COMPONENT card (button switch, divider, cross-board
output) — NOT by the internal pull alone — so INPUT_PULLUP pins wired to
event-driven parts with no SPICE model (rotary encoder, keypad) are left to the
part layer and never clobbered. AVR only; RP2040/STM32 stay on the part-seed
until their pulls are modeled.
The spiceDrivenInputs change (e81450e + f4401cc) fixed plain-INPUT-wired-to-rail
reads but BROKE the far more common INPUT_PULLUP + button-to-GND pattern: the
internal pull-up is not modeled in the netlist, so the input floated LOW and read
as permanently pressed (verified live on the stm32-bluepill-button example).
Revert all the spice-driven-input changes to the pre-fix part-seed behaviour,
which handles INPUT_PULLUP correctly. Proper fix (model the internal pull-up per
board so BOTH patterns work) is a follow-up. Keeps the Pi LED fix.
Extend the source-backed SPICE-driven input fix to the Pico (RP2040) and STM32:
a GP/PA pin wired to a rail or button now reads the right level from the solve,
while floating event-part nets (encoder/keypad/dialer/dip/stepper) stay on the
part layer. RP2040 just opts in (spiceDrivenInputs); STM32 opts in via the
Stm32BridgeShim and connectDigitalInputsToMcu maps PA0/PC13 names to the linear
pin setPinState expects (stm32PinNameToLinear).
An Arduino input wired to a power rail read the wrong level: a pin tied to 5V
read LOW, and a button-to-5V read idle-HIGH / pressed-LOW. AVR inputs were never
fed the solved circuit voltage (only the ESP32 had spiceDrivenInputs), so a
bare-rail input had no driver and buttons fell back to a hardcoded active-low
pull-up seed that ignored the wiring.
Enable spiceDrivenInputs on AVRSimulator, and gate connectDigitalInputsToMcu on
a new NetlistBuilder sourcedNets set (rails, GPIO V-sources, pulls, and any net
a component card touches). Only source-backed input pins are driven from the
solve; floating nets are left to the part layer, so event-driven parts with no
SPICE model (rotary encoder, keypad, dialer, dip-switch, stepper) keep driving
their own pins instead of being forced LOW.
/about had its own seoMeta but was never in the entry-server prerender map,
so it was served as the SPA shell (homepage title/canonical) — a soft-404
risk for a page that is in the sitemap. Add it to ROUTE_COMPONENTS so
prerender-seo.mjs emits dist/about/index.html with the real About content
(now featuring the Velxio 3.0 release card) and a self-referencing canonical.
ESP32 digitalRead now reflects the actual circuit instead of a part-level
seed, so a button behaves like hardware — including breaking when it's
mis-wired.
- connectDigitalInputsToMcu: after each SPICE solve, threshold every ESP32
input pin's net voltage (3.3 V LVCMOS, hysteresis) and push the level into
QEMU. Only pins the MCU isn't driving as outputs are injected.
- Esp32BridgeShim advertises spiceDrivenInputs; the pushbutton / 6mm-button /
slide-switch parts skip their direct setPinState seed for such boards and
only flip the component property (pressed/value), which re-solves the
circuit. The connector then decides the level from the real wiring.
- makePinPullHandler no longer seeds the pin; it only records the pull
(netlist resistor) + requests a re-solve, so the read stays circuit-driven.
- GROUND_PIN_RE now matches bare numbered grounds (GND2, GND3) — the ESP32
DevKit element labels its second pad 'GND2', which previously floated.
Net effect: a correctly-wired INPUT_PULLUP button idles HIGH and reads LOW
pressed; a button mis-wired with GND on the wrong terminal reads stuck-LOW,
matching real silicon. AVR / RP2040 keep the legacy part-seed path.
The Pi bridge onPinChange was a no-op, so guest GPIO writes never reached the
PinManager / SPICE solver and wired LEDs stayed dark even though user scripts
printed 'LED on'. Mirror the ESP32 branch: forward to pm.triggerPinChange so
GPIO drives the canvas. Interconnect still preserves and calls this before its
own cross-board routing.
makePinPullHandler drove the post-boot INPUT_PULLUP seed through
getBoardBridge(), which only indexes the Pi bridge map (bridgeMap) — for
an ESP32 it returned undefined and the sendPinEvent seed silently no-op'd,
so the digital input stayed LOW even though the pull config was read and
the SPICE net showed the pulled voltage. ESP32 bridges live in
esp32BridgeMap; use getEsp32Bridge().
Completes the internal-pull emulation for the common case (a button on an
RTC-capable GPIO like 4/15/25/... with INPUT_PULLUP):
- Backend reads the RTC_IO pad RUE/RDE bits via the new
get_internals(QEMU_INTERNAL_RTCIO) and emits gpio_pull for RTC pins, so
pull-up/down on those pads is finally visible (it lives in RTC_IO, not
IO_MUX). IO_MUX path still covers non-RTC pins.
- The digitalRead path is driven by seeding the GPIO input level, not by
SPICE. The part-level INPUT_PULLUP seed (BasicParts) is sent at attach,
before the multi-second QEMU boot finishes, so it is lost and the pin
reads LOW. makePinPullHandler now drives the pin to the pull's idle level
via sendPinEvent when the guest programs the pull (post-boot), so it
sticks. A real button press/release still overrides it.
INPUT_PULLUP / INPUT_PULLDOWN had no effect in simulation: the ESP32's
internal pull resistors live inside QEMU and were invisible to the SPICE
solver, so an input wired to a button-to-GND floated to 0 V and read LOW
even at idle. The canonical active-low button never worked.
Read the pull config straight out of the running guest: the IO_MUX
register (FUN_PU bit 8 / FUN_PD bit 7) is already exposed read-only via
qemu_picsimlab_get_internals(3), so no QEMU rebuild is needed. The worker
scans it on the 100 ms poll thread and emits gpio_pull; the bridge feeds
it to PinManager; the netlist stamps a weak 45k resistor to the rail so
idle inputs read the correct level. 45k matches the real internal pull
and is weak enough that any external driver/pull dominates.
Verified with ngspice: idle ~3.3 V (HIGH), pressed ~0 V (LOW).
The pushbutton was modelled as a switch between only 1.l and 2.l; the
other two legs (1.r, 2.r) connected to nothing. Wiring GND/GPIO to those
legs silently produced a dead button, and the failure was invisible.
Model it like hardware: 1.l is internally shorted to 1.r and 2.l to 2.r,
and pressing bridges terminal 1 to terminal 2. Wiring to any leg now
works, and putting GPIO and GND on the same terminal is a dead short,
exactly as on a real tactile switch. Back-compat A/B variant preserved.
- boot_images manifest: bump arm64 rootfs (gpiozero/colorzero baked in,
hostname applied at boot, reworded MOTD)
- RaspberryPi3Bridge: onBooted shell-ready detector + sendAndWaitForPrompt
flow control (resets on disconnect)
- RaspberryPiWorkspace: distinct Booting overlay + piBooted-driven status,
inline SVG icons replacing emoji glyphs
- SerialMonitor: strip CSI/DSR escapes so the dumb console no longer shows
a literal [6n next to the prompt
- VirtualFileSystem: upload auto-starts the Pi and waits for the shell, then
flow-controls each command (no more dropped lines on large files)
- i18n: bootingTitle/bootingNote + reworded offlineNote2 across 9 locales
Sweep all off-brand blues (#007acc logo-blue, #0e639c, #3b82f6) and the neon
cyan family (#4fc3f7, #00b8d4, #00e5ff, rgba 0,184,212 / 0,122,204) across the
editor, simulator, examples gallery and pages to var(--color-action-primary).
The Code/Both/Circuit toggle, board chips, library manager, modals etc. now
match the Libraries / +Add buttons. Also keep the editor Libraries label
visible in the default split (lower the container-query threshold).
Unify the editor toolbar and landing page on the single #0071e3 accent
(token --color-action-primary). Replace the fluorescent cyan/green outline
treatment (Libraries pill, overflow icons, compile/run/stop, feature tiles,
pricing/licensing badges, classroom banner) with solid fills following the
+Add button. Green/red kept solid and semantic-only (run/success, stop/error).
recordUpdateWire was used by the wire colour palette and the right-click menu but
never destructured from the store, so every colour-swatch click threw
'recordUpdateWire is not defined' and did nothing. tsc would have caught this, but
build:docker skips type-checking, and the only prior caller (the touch-only palette)
was never exercised. Bind it like the other record* actions. Together with the
applyNow fix this makes wire colour changes from the UI actually work.
recordUpdateWire pushed its command with { applyNow: false }, so it recorded the
change for undo but never executed it. Its only callers (the wire colour palette
and the new right-click menu) pass the new colour and expect it applied — neither
pre-applies via the raw updateWire mutator. Net result: changing a wire colour
from the UI did nothing (only the 0-9/c/l/m/p/y keyboard shortcut, which calls
updateWire directly, worked). Drop applyNow:false so it applies like every other
record* command (recordRemoveWire etc.). Adds an undo/redo regression test.
Changing a wire's color on desktop was keyboard-only (select wire + 0-9/c/l/m/p/y)
with no visible control — the floating color palette (SelectionActionBar) only
rendered on touch devices, so desktop users had no way to discover it. Now:
- the wire SelectionActionBar (top-center, with the color palette) also shows on
desktop when a wire is selected and the sim is stopped (it is pinned top-center
so it never covers pins); component/board bars stay touch-only.
- right-clicking a wire opens a context menu with the color swatches + delete.
Keyboard shortcuts still work. Mirrors the existing board context-menu pattern.
SSD1306Core only handled horizontal/vertical addressing (0x20/0x21/0x22) and
defaulted memMode to horizontal. Page-mode drivers (Tiny4kOLED on ATtiny85,
U8g2 page buffer, classic SSD1306 libs) position the cursor with the single-byte
commands 0xB0-0xB7 (page) and 0x00-0x0F / 0x10-0x1F (column nibbles) and rely on
the SSD1306 power-on default of PAGE addressing — they never send 0x20. velxio
ignored those cursor commands and advanced in horizontal mode, so every setCursor
was a no-op and the hatching/border/text piled onto wrong rows -> garbled display.
Fix: default memMode=2 (datasheet power-on) and handle the page/column-set
commands. Adafruit_SSD1306 still works (it sends 0x20,0x00 + 0x21/0x22 explicitly).
Verified: decoded the real ATTinyCore Tiny4kOLED I2C stream renders a clean
border + '128x64'. Adds a page-addressing render test.
The ATtiny85 has no hardware TWI; TinyWireM/Tiny4kOLED drive I2C through the USI
peripheral (SDA=PB0, SCL=PB2). avr8js ships AVRUSI but velxio never instantiated
it, so the I2C bus had no master on the ATtiny85 and devices (e.g. SSD1306 OLED)
got no data — the display stayed blank (and wokwi-ssd1306 threw putImageData with
an empty framebuffer). New UsiI2cBridge instantiates AVRUSI and sniffs the SDA/SCL
lines, replaying START/STOP + 8-bit bytes onto the shared I2C bus as
start/connectToSlave/writeByte/stop (the same calls AVRTWI makes for the Uno).
Validated against real ATTinyCore Tiny4kOLED firmware: decodes addr 0x3C + SSD1306
init/data stream. Firmware tolerates NACK so the sniffer is passive.
arduinoPinToName() had no ATtiny85 case, so pin 1 reverse-mapped to "1"
instead of "PB1" (the wire/netlist name). The MCU-edge listener was never
attached (name not in pinsInCircuit) and the SPICE V-source was never altered
on digitalWrite, so a blink LED's branch current stayed at its HIGH value —
the LED latched ON and never turned off (and analogWrite duty changes never
re-solved). Map attiny85 pin N -> "PBN", mirroring pinNameToArduinoPin.
AVRSimulator used wrong ATtiny85 Timer0 data-space addresses: OCR0A 0x56
(=PINB), OCR0B 0x5c (=EECR), TCCR0A 0x4f (=TCNT1). analogWrite() writes
OCR0B at data 0x48, so pollPwmRegisters() read the wrong register and PWM
duty was never seen — attiny85-pwm-fade showed no fade. Corrected both
PWM_PINS_TINY85 and attiny85Timer0Config to TCCR0A=0x4A/OCR0A=0x49/OCR0B=0x48
(verified against the ATTinyCore analogWrite disassembly). delay()/millis
(overflow-based) was unaffected. Tests updated off the old 0x5c/0x56.
The live solver only re-solved on component/wire/board changes, so a runtime
burnout (which changes burntComponents, not components) wouldn't rebuild the
netlist — the burnt part stayed in the circuit until something else changed.
Trigger a re-solve on burntComponents change too. The monitor skips already-
burnt parts, so this converges (one extra solve).
- The live solver now excludes runtime-destroyed components from the netlist,
so a burnt part actually goes OPEN: its current stops and anything it fed
loses power (cascading failure), the way real hardware behaves once a part
burns out. Filter is in CircuitSimulationService.runSolve (no-op when nothing
is burnt).
- The LED's burnout now also marks it in the shared burntComponents set, so a
burnt LED gets the same charred + smoke-badge visual (and is opened in the
solve) as a resistor / capacitor, on top of going dark.
Generalizes the LED's burnout to passive parts via a centralized monitor that
watches the live electrical solve. When a part is stressed past its rating for
a sustained moment it's marked "destroyed": the canvas renders it charred with a
smoke badge and a fault is logged to the output console. Clears on Reset.
Follows the Fritzing-simulator precedent (smoke-on-component) wrapped in a
first-order thermal delay so a brief inrush spike doesn't destroy a part — only
sustained overload (or a catastrophic >=3x overload, instant) does.
- runtimeBurnout.ts: pure stress (resistor power, cap voltage / reverse) + a
thermal-delay burn decision, plus a monitor subscribed to the electrical +
simulator stores. Resistor burns past 2x rated (the verifier already warns at
1x for intentional teaching over-power); a cap bursts over its voltage rating
or on reverse polarity.
- useSimulatorStore: burntComponents set + mark/clear actions; cleared on
Reset / restartParts.
- DynamicComponent + SimulatorCanvas.css: charred filter + smoke badge.
Tests: thermal-delay decision (instant / sustained / spike / cooldown) + stress
computation (resistor power, cap over-voltage, reverse, unwired -> null).
- Power short (blocking error): a wire joining a VCC-type pin directly to a
GND-type pin shorts the supply to ground. The current-based short-circuit
rule only inspects battery/signal-generator/power-supply sources, so it
misses a board-rail-to-GND short with no such source -> name it structurally.
- Shorted-out part (warning): a 2-terminal part with both terminals on the same
node has no effect on the circuit.
Both graph-based, run before the solve. Zero false positives across the 69
gallery examples; gallery pre-flight tests still pass (no spurious blocking).
First slice of the connection ("malas conexiones") checks, graph-based and run
before the solve so they report even on circuits too incomplete to solve:
- Missing power: a rated peripheral (sensor/display) wired into the circuit but
missing its VCC or GND connection -> warning. Boards are excluded (they live
in input.boards and self-power).
- Dangling 2-terminal part: a resistor / LED / capacitor / diode / inductor
connected on only one side (the other terminal floating) -> warning.
Both non-blocking. Verified zero false positives across all 69 gallery
examples. Tests: dangling resistor warns, fully-wired doesn't, module missing
GND warns.
Extends the over-voltage rule to the two cases the previous slice deferred:
- Boards (ESP32 / Pico / Arduino / ...): a board's supply pins all collapse to
the self-driven vcc_rail net, so an external source on them makes the .op
singular rather than readable. Added a graph-based check (runs before the
solve): if a power source is wired to a board supply pin and its nominal
voltage exceeds that pin's rating, warn. Threaded boardKind into
BoardForSpice so the verifier can look up the board rating.
- Electrolytic capacitors: new `voltage` rating property (select, default 25V,
on capacitor-electrolytic + cap-elec-* presets, via component-overrides +
regenerated metadata). The verifier reads the DC voltage across the +/- pins
and warns on over-voltage (vent/burst) and on reverse polarity (a polarized
cap wired backwards). Defaults to 25V when the property is unset.
Tests: 9V battery -> ESP32 VIN warns, 1.5V doesn't; 24V across a 16V cap warns,
5V across a 25V cap doesn't; reverse-biased cap warns. All real-ngspice.
handleCompile() wiped all logs at the start, including the 'Circuit check'
group the pre-flight verifier had just logged (e.g. an over-voltage warning).
A Run auto-compiles right after verification, so the warning vanished. Preserve
circuit-check entries on compile, same as the boardless path already did.
Adds a non-blocking circuit-verifier rule: a component whose supply pin sees
more than its datasheet absolute-maximum voltage warns ("X V on the VIN pin --
above its Y V maximum; not emulated accurately"). This is the "fed too much
voltage" mistake the operator asked for (a 3.3-5V module wired to a 9V battery).
- New componentRatings.ts: per-PIN abs-max table (SSD1306/ILI9341 displays,
DHT/BMP280/HC-SR04/MPU6050 sensors, NeoPixel, servo). Per-pin thresholds so a
3V3 pin (3.6V) and a VIN pin (6V) are judged separately. Unknown parts are
simply not checked; an unwired or floating supply pin is skipped.
- circuitVerifier reads each rated part's supply-vs-ground voltage from the
solved nets (via pinNetMap) and warns when it exceeds the rating.
- VCC/VDD/3V3/5V pins ride the shared vcc_rail net (NetlistBuilder convention);
VIN is a normal net. Both handled.
- Tests: 9V on a module VIN warns; 5V on VIN does not; a 3.3V pin on a 5V rail
warns.
Boards (esp32/pico/arduino) carry ratings in the table but aren't checked yet
-- BoardForSpice doesn't thread its boardKind; follow-up.
Clicking Run runs a pre-flight circuit-verification SPICE solve before
compiling. On a cold ngspice worker that solve takes a second or two, but the
Run button kept showing the play icon and stayed enabled, so it looked dead
and got clicked repeatedly -- each click stacking another verification (the
reported 6x [handleRun] click).
- Add a `verifying` state: the Run button now shows the same spinner as the
Compile button and is disabled while the pre-flight solve runs.
- Synchronous re-entrancy guard (runInFlightRef) ignores re-clicks while a
verification is already in flight.
The runtime burnout / pre-flight messages used an inline `setMessage` toast
that rendered as a bar near the Run/Stop buttons and overlapped them. Route
all circuit findings into the compile output console instead — one unified,
red/orange diagnostics log next to the compiler output (Proteus-style):
- New "Circuit check" console group (CIRCUIT_CHECK_TARGET). checkOrBlock logs
every error (red) / warning (orange) there and opens the console; the
blocking modal is kept for the explicit Run-anyway / Cancel decision.
- Runtime `velxio-circuit-fault` events (LED burnout) log to the same group
instead of the toast; no auto-open (the continuous solver can fault on load).
- Warnings-only no longer pop a toast — the console entry is the record.
- The run-path clears preserve circuit-check entries so findings survive a
"Run anyway" auto-compile.
The Run (and Run All) buttons were wired `onClick={handleRun}`, so React
passed the click event as the first argument. handleRun(skipVerify=false)
then treated the truthy event as skipVerify=true and skipped checkOrBlock
entirely -- the pre-flight circuit verifier never ran on a button click.
This is the real reason a 9V battery wired straight to an LED ran with no
warning even though the verifier exists and is correct (project 2840fd12).
- onClick={() => handleRun()} and onClick={() => handleRunAll()} so
skipVerify stays at its false default.
- Give handleRunAll the same checkOrBlock pre-flight gate handleRun has.
Verification failing silently in production is otherwise hard to spot — the
rules read 0 A when branch currents are missing. Log the errors/warnings,
whether a solve landed, and which branch/node vectors came back.
The pre-flight circuit verifier reads branch currents via runNetlist ->
readAllCurrentVectors() (ngSpice_AllVecs enumeration). The production
Web-Worker ngspice WASM build does not surface voltage-source #branch
vectors through that enumeration for an .op plot, so branchCurrents came
back empty and every current rule (short-circuit, LED over-current) read
?? 0 -> no fault. The live solver avoided this by requesting each current
explicitly by name; the Node test build enumerates them, so the gap was
invisible to the suite. Net effect: a 9V battery wired straight to an LED
ran with no warning (reported on project 2840fd12).
- runNetlist: request every V_* source branch current explicitly by name
and merge with the enumeration, so source/LED currents are always present
regardless of the worker WASM's AllVecs behaviour.
- circuitVerifier: non-finite source/LED current -> blocking unstable-solve
fault ("could not solve a stable current - likely a short or a part with
no current limit, e.g. an LED with no series resistor").
- LED runtime (BasicParts): burn out on a non-finite current instead of
falling through to the digital fallback and glowing; raise burnout
threshold 20mA -> 100mA so high-power/RGB channels are not falsely
destroyed; clear the burnt latch on Reset (resetBoard bumps hexEpoch).
Tests: real-data repro, mocked non-finite verifier test, runtime
non-finite / high-power / latch-recovery tests.
All three bugs are rotated components whose pin geometry is computed in a
path that ignores the rotation, so pins/wire-starts land tens of pixels off
the visual pin tips. The live rotate action already recalculates correctly;
these are the paths that didn't.
#231 (context-menu 'Tap a pin to wire'): both onPinSelect handlers in
SimulatorCanvas computed the wire start as getBoundingClientRect().left +
pin.x — adding the UNROTATED pin offset to the ROTATED bounding-box corner.
On a 90-deg HC-SR04 that put the start ~70-100px off (measured). Replaced
with calculatePinPosition(id, x+6, y+6, rotation), the same rotation-aware
helper wires and the pin overlay use.
#232 (rotate -> delete -> undo): recordRemoveComponent's undo restored the
component + wires but never recalculated wire endpoints, so a rotated part's
wires kept the unrotated coords captured at delete time. Added a
requestAnimationFrame updateWirePositions(id) after restore.
#230 + #232 (pin boxes wrong after import / undo / load, 'fixes if rotated
again'): PinOverlay captured the wrapper's layout box (the rotation pivot)
once at mount. On import/undo/load the component mounts already-rotated and
its wokwi-element may not be sized on the mount tick, baking a wrong pivot
that only refreshed when rotation changed. PinOverlay now re-measures after
layout (rAF) and whenever it is about to become visible (showPins dep).
AVRSimulator never instantiated avr8js's AVREEPROM peripheral, so any
EEPROM.read/write/update hung the sketch: the Arduino EEPROM library spins
on `while (EECR & (1<<EEPE))` waiting for the write-complete bit to clear,
and with no peripheral driving EECR that bit never cleared (issue #203 —
EEPROM.update(0,123) + EEPROM.read(0) hangs instead of printing 123).
Wire AVREEPROM to the CPU in both loadHex() and reset() via a new
attachEeprom() helper. The EEPROMMemoryBackend is created once per
simulator instance and reused across firmware reloads and resets, so a
value written in one run is still readable on the next boot — matching
real hardware, where re-flashing leaves EEPROM intact. Sizes per variant
(Uno 1024 B, Mega2560 4096 B, ATtiny85 512 B); ATtiny85 gets its own
register map (EECR 0x3C / EEDR 0x3D / EEARL 0x3E / EEARH 0x3F) since
avr8js's default eepromConfig targets the ATmega328P.
Adds eeprom.test.ts: drives the EEPROM register protocol against the
production AVRSimulator (loadHex + step), asserting a byte round-trips,
the EEPE poll terminates (no hang), and contents survive a reset.
The NTC breakout's SPICE topology was inverted relative to the example
sketch's decode formula (rNtc = R_PULL * v / (5 - v)), which assumes a 10k
pull-up from VCC to OUT and the NTC from OUT to GND. The mapper had the NTC
on top (VCC->OUT) and the pull-down on the bottom, so the recovered
temperature ran backwards: dragging the slider to 100C made the sketch
print -25C. Swap the two resistors so V_OUT = 5 * Rntc / (Rntc + Rpull),
matching the sketch and the hand-built reference netlist in
spice-avr-mixed.test.ts (T=0 -> ADC 789, T=25 -> 511, T=50 -> 270).
Also replace the SensorParts linear approximation (2.5 - (t-25)*0.02) with
the same beta-model divider so the non-SPICE ADC injection decodes back to
the slider value, and drop the dead onInput path that treated the element's
value as a raw ADC count.
Reset now restores interactive sensors (temperature/lux/gas sliders) to
their configured defaults: resetBoard re-dispatches each sensor's default
into the running sim and bumps sensorResetNonce so the open
SensorControlPanel remounts and the slider snaps back. Previously a restart
left the NTC frozen at the last dragged temperature.
Updated the examples netlist snapshot for the swapped NTC cards.
The star banner used a single localStorage flag (velxio_star_prompted)
set identically whether the user clicked through to the repo or just
closed it, so once dismissed it never showed again and clickers and
closers were indistinguishable.
Now track three flags:
velxio_star_prompted - dismissed the first ask
velxio_star_prompted_v2 - dismissed the follow-up (stop forever)
velxio_star_clicked - clicked through to the repo (stop forever)
Anyone who dismissed the first ask without clicking through gets ONE
follow-up (round 2) with a stronger message; clicking the repo link at
any time opts them out permanently. Capped at two asks total.
Adds starBanner.title2/body2 copy in all 9 locales.
Commit 9360f95 deleted lib/proWifiGate.ts but left useSimulatorStore importing
it (the store edits weren't staged), so a clean checkout of master failed to
build (import of a deleted module). velxio.dev was unaffected — deploy.sh builds
from the working tree, which had the removal applied. Commit the removal so HEAD
is consistent.
The proWifiGate seam blocked a free user from running ANY Pico W WiFi sketch.
The product model changed: LOCAL WiFi (the chip associating to the simulator's
virtual AP) is now FREE — only REAL internet (the backend bridge) and the IoT
gateway are paid, gated inside the pro overlay's Cyw43PioPeripheral / backend.
So a free user must be allowed to run WiFi sketches. Remove the gate seam and
its two store call sites. The board-kind firmware variant + the run-time
peripheral re-attach (which fixed the plain-firmware import-network crash) stay.
Two robustness fixes for the paid-WiFi open-core split:
1. A pi-pico-w board now boots the RPI_PICO_W firmware variant (which has the
`network` module) based on its BOARD KIND, not on whether the WiFi
peripheral happens to be attached. Previously the variant was
`pioPeripheral ? 'pico-w' : 'pico'`, so any moment the peripheral was
absent (see #2) booted the plain Pico firmware and a Pico W sketch crashed
with "ImportError: no module named 'network'". Store boardKind in
attachPioPeripheral and pick the variant from it. (OSS: 'pico-w' isn't
registered, so firmwareConfig falls back to 'pico' — a self-hosted Pico W
has no WiFi engine anyway.)
2. Re-attach the PIO peripheral in loadMicroPythonProgram before loading
firmware. An example deep-link adds the board during render, which races the
pro overlay's async mountPro that installs the CYW43 factory — so the
board-add attach returned null and a PAID user's Pico W booted plain
firmware too. attachPioPeripheral is idempotent; by run time the factory is
installed, so a paid user gets the W peripheral and real WiFi.
Pico W WiFi is a paid overlay feature. A free/web user running a Pico W sketch
that uses WiFi had no peripheral attached -> the simulator picked the plain Pico
firmware (no `network` module) -> the run crashed on `import network` with a
raw Python traceback (on a public example page, no less).
Add lib/proWifiGate.ts (mirrors proBoardGate): a stable doorbell the overlay
fills in. useSimulatorStore gates both loadMicroPythonProgram (before loading
firmware) and startBoard (run backstop for example/loaded boards): if the gate
blocks, fire the upgrade prompt and skip the run. Non-WiFi Pico W sketches still
run for free. No-op in OSS (default 'allow' -> a Pico W runs as a plain Pico).
The Pico W WiFi showcase examples are a paid-overlay feature now (the WiFi
engine moved to the overlay). Read them through a build-time `@pro` seam so the
SSR prerender + gallery + sitemap include them when built with the overlay, and
OSS gets an empty stub.
- data/examples.ts: import { proExamples } from '@pro/data/proExamples' (static,
build-time) instead of the local examples-picow-wifi.ts; delete that file.
- src/__pro_stub__/data/proExamples.ts: OSS no-op (empty list) for the @pro alias.
- vitest.config.ts: mirror the @pro alias (stub by default / overlay when
VITE_PRO_BUILD) so tests loading examples.ts resolve it.
- scripts/generate-sitemap.mjs: also parse <PRO_OVERLAY_PATH>/data/proExamples.ts
when building with the overlay (the script reads example IDs from source text,
so it can't follow the alias).
- Tests: drop the picow-wifi import/usage from the 5 OSS example tests (they
validate the OSS set now); prune the 4 obsolete picow netlist snapshots. The
overlay's proExamples get their own coverage in pro/.../__tests__/.
David Montero Crespo