Adds 44 SPICE mappers, 58 custom metadata entries, and 12 visual
Web Components covering logic gates, transistors, op-amps, regulators,
sources, electromechanical parts and integrated-circuit packaging.
Fase 9 — component catalog expansion
------------------------------------
- 7 logic gates (AND/OR/NAND/NOR/XOR/XNOR + NOT) as SPICE B-sources
- 8 multi-input gates (AND/OR/NAND/NOR with 3 and 4 inputs)
- 9 transistors: 5 BJTs (incl. PNP 2N3906/BC557) + 4 MOSFETs (incl.
P-channel IRF9540/FQP27P06). NMOS refactored from Level=3 W=0.1
(hangs ngspice) to Level=1 with sane W/L
- 5 op-amps: LM358, LM741, TL072, LM324 with per-chip saturation
rails + opamp-ideal
- 4 linear regulators (7805, 7812, 7905, LM317) with dropout
- 3 batteries (9V, AA, coin-cell) with realistic ESR
- Signal generator (sine / square / DC)
- 2 Schottky diodes (1N5817, 1N5819) + photodiode (lux-driven
current source)
Fase 10 — electromechanical + ICs
---------------------------------
- Relay (SPDT): coil + L + S-switch with native hysteresis +
flyback diode, inverted-control trick for the NC contact
- Optocouplers 4N25 and PC817 (LED + CCCS with CTR=0.5 / 1.0)
- 7 74HC ICs as DIP-14 packages emitting 4 or 6 B-sources per
component (first mapper pattern emitting multiple device cards)
- 3 flip-flops (D, T, JK) — digital-sim only (edge detection is
not representable in ngspice .op)
- L293D dual H-bridge motor driver
Infrastructure
--------------
- scripts/component-overrides.json gains a _customComponents[] array
that lets new Velxio-only parts survive metadata regeneration
(previously applyOverrides() could only patch wokwi-elements
components that had already been scanned)
- scripts/generate-component-metadata.ts injects custom entries
before the patch loop
- New ComponentCategory values: 'logic', 'analog', 'electromech'
- frontend/src/components/DynamicComponent.tsx PASSIVE tracing
extended from just ['resistor','resistor-us'] to 9 two-terminal
passives with per-part pin name maps
- New CI workflow test-circuit.yml runs the sandbox on push/PR
- frontend-tests.yml regenerates metadata and fails if committed
JSON is stale
- Documented 2 new ngspice gotchas in circuit-emulation-gotchas.md:
unicode in netlist titles silently hangs the parser, and
MOSFET Level=3 + W=0.1m causes .op to hang
- 164/164 sandbox tests passing in ~9 s (was 88 pre-fase-9)
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
- Implemented Bmp280Element as a custom web component for the BMP280 barometric sensor, including SVG representation and pin configuration.
- Created CircuitPreview component to render circuit thumbnails using SVGs of components, including support for various boards and components.
- Added a script to generate SVG files from wokwi-elements, ensuring proper formatting and structure for reliable rendering.
- Introduced a test HTML generation script to visualize component SVGs.
This commit introduces a detailed markdown document outlining the process of simulating DHT22 and HC-SR04 sensors on the ESP32 platform using Velxio's QEMU fork. The documentation covers the context of the simulation, key callbacks, problems encountered, and solutions implemented for both sensors. It includes architectural details, end-to-end testing procedures, and guidelines for adding new GPIO-timed sensors. The aim is to provide maintainers with a thorough understanding of the GPIO logic and the challenges faced during development.
- Updated the threshold for switching to data mode in MPU6050Slave from 2 to 3 WHO_AM_I reads to ensure correct chip identification.
- Enhanced comments in the code to clarify the sequence of I2C events during initialization.
- Added a new test file `test_mpu6050_emulation.py` to validate the MPU6050Slave state machine and ensure it handles the full Adafruit_MPU6050::begin() event sequence correctly.
- Updated existing tests to reflect the changes in the I2C handling logic.
- Modified `components-metadata.json` to update the generated timestamp.
- Marked submodules `rp2040js` and `wokwi-elements` as dirty to reflect local changes.
- Updated components-metadata.json with new generated timestamp.
- Refactored Esp32C3Simulator.ts to remove unnecessary debug variables and logging, and added support for additional ROM functions.
- Modified useSimulatorStore.ts to clarify bridge usage for ESP32 boards.
- Updated submodules for QEMU and other libraries to indicate dirty state.
- Added test_esp32c3_emulation.py for end-to-end testing of ESP32-C3 emulation, including compilation, flash image merging, and GPIO event checking.
- Added detailed logging for GPIO changes, system events, and errors in simulation websocket.
- Improved ESP32 firmware handling by merging individual binaries into a single 4MB flash image.
- Updated ESP32 bridge to handle serial output and GPIO changes with appropriate logging.
- Introduced integration test for ESP32 emulation, covering compilation, WebSocket connection, and event handling.
- Enhanced examples to include ESP32 projects and updated the examples gallery to reflect new board types.
- Refactored simulator store to manage ESP32 bridge and simulator instances more effectively.
- Updated requirements to include esptool for ESP32 firmware management.
Keep only build_qemu_step4.sh (the DLL relink step used in production).
Deleted: build_qemu_dll.sh, build_qemu_step3.sh, check_tools.sh,
fix_distlib.sh, fix_distlib2.sh, install_git.sh, install_meson.sh
(all were used once during initial DLL compilation setup)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
- Added LogicGateParts.ts for simulating various logic gates (AND, NAND, OR, NOR, XOR, NOT).
- Introduced ProtocolParts.ts for simulating I2C and SPI components including SSD1306 OLED, DS1307 RTC, MPU6050 IMU, DHT22 sensor, HX711 load cell, IR receiver, IR remote, and MicroSD card.
- Implemented BasicParts.ts with a membrane keypad and rotary dialer simulations.
- Enhanced SensorParts.ts with a single NeoPixel and PIR motion sensor.
- Updated index.ts to include new parts for logic gates and protocols.
- Modified vite-env.d.ts to declare new custom elements for the added components.
- Introduced new SensorParts.ts to handle various sensors including tilt switch, temperature sensor, gas sensor, flame sensor, heart beat sensor, and sound sensors.
- Implemented stepper motor simulation with full-step decoding.
- Added utility functions for ADC voltage injection in partUtils.ts, supporting both AVR and RP2040.
- Updated BasicParts.ts to avoid re-registering the 7-segment display.
- Enhanced ComplexParts.ts by removing unused ADC helper functions.
- Updated index.ts to include the new SensorParts module.
- Updated Vite environment definitions to include new custom elements for sensors and stepper motors.
- Add LoginPage and RegisterPage for user authentication.
- Create UserProfilePage to display user projects.
- Implement ProjectPage for viewing and editing individual projects.
- Introduce authService for handling user login, registration, and session management.
- Add projectService for managing project data retrieval and manipulation.
- Enhance EditorPage with file management capabilities and save prompts.
- Introduce Zustand stores for managing authentication, editor state, and project state.
- Add reserved usernames utility to prevent certain usernames during registration.
- Update compilation service to handle multiple files for Arduino sketches.
- Removed outdated WOKWI_LIBS.md and replaced with updated documentation.
- Added ARCHITECTURE.md to describe project structure and data flow.
- Created SETUP_COMPLETE.md for installation and configuration instructions.
- Implemented automatic update script for Wokwi libraries.
- Updated frontend components to utilize local Wokwi libraries.
- Enhanced AVRSimulator to manage peripherals more efficiently.
- Added example screenshot generation instructions for better documentation.
- Updated components metadata and ensured proper integration with Vite.
- Updated components-metadata.json with new generation timestamp.
- Added event handling for button presses and releases in DynamicComponent.
- Improved ExamplesGallery with new styles for placeholders and previews.
- Introduced LCD 20x4 display example with corresponding code and wiring.
- Enhanced SimulatorCanvas to subscribe components to pin changes.
- Implemented PartSimulationRegistry for managing component simulation logic.
- Added basic and complex parts simulation including pushbuttons, LEDs, and LCDs.
- Created utility functions for capturing canvas previews and generating SVG previews for example projects.
- Created a new TypeScript file for component metadata types defining structure for dynamically loaded components.
- Implemented a metadata generator script that scans the wokwi-elements repository to extract component information, including properties and categories.
- Added package.json and package-lock.json for dependency management, including TypeScript and related tools.
- Introduced a new file to log ping statistics for testing purposes.
David Montero Crespo