ATtiny85 (AVRSimulator + collectPinStates + connectAnalogInputsToMcu + SimulatorCanvas + Attiny85Element + examples):
- Add attiny85AdcConfig with correct register addresses (ADMUX=0x27,
ADCSRA=0x26, ADCSRB=0x23, ADCL=0x24, ADCH=0x25, DIDR0=0x34, adcInterrupt=0x08).
Without this, analogRead() polled the wrong address forever and the
firmware hung on first ADC read.
- Add attiny85Timer0Config + instantiate AVRTimer so OVF fires at the
ATTinyCore-expected ~1.024 ms cadence. delay() advance is still blocked
on avr8js TIFR auto-clear semantics (separate upstream issue, see
ATTINY85_TIMER0_UPSTREAM_ISSUE.md in velxio-prod test plan).
- Map ATtiny85 ADC channels to PB-style pin names (PB5/PB2/PB4/PB3 -> 0..3)
in connectAnalogInputsToMcu so SPICE node voltages reach the right ADC
channel.
- Recognise /^PB\d+$/ in collectPinStates.pinNameToArduinoPin so wires
named "PB1" emit v_attiny85_pb1 V-source and the LED responds to MCU
writes. Previously every PB-wire returned -1 and SPICE saw no source.
- SimulatorCanvas: subscribe pin 1 (PB1) for the built-in LED on the
attiny85 board kind (Digispark convention), instead of falling through
to the pin-13 default.
- Attiny85Element: remove the hand-drawn "yellow LED" circle that was
floating above the chip. The bare DIP-8 has no on-board LED; examples
wire a real wokwi-led + resistor instead.
- examples.ts: add a real wokwi-led + 220 Ohm wokwi-resistor + wires to
attiny85-blink, and add missing series resistors to attiny85-button-led
and attiny85-ntc-sensor. attiny85-pwm-fade was already correct.
Custom-chip pipeline (CustomChipPart + simulatorBridges):
- Add a requestAnimationFrame loop that calls instance.tickTimers() every
frame in CustomChipPart. Chips that register vx_timer_create (e.g. an
i8080 stepping its core, or a sensor publishing samples) had timers
added to the queue but nothing fired them; tickTimers was dead code.
- Gate the ESP32 backend path with detectSimulatorKind(sim)==='esp32'.
The previous `typeof sim.registerSensor === 'function'` check matched
AVR and RP2040 simulators too (they expose registerSensor for I2C
sensor proxies), routing client-side chips to a non-existent ESP32
worker on those boards.
- Replace direct simulator.usart.writeByte calls in avrUartTx with a
JS-level FIFO + setTimeout(1ms) drainer. avr8js writeByte drops bytes
under burst load (a chip emitting print_string lost ~99% of bytes via
non-immediate, or kept only the last byte via immediate). The drainer
attempts one non-immediate write per tick and retries on RXC busy /
RXEN off. Added a guard for ATtiny85 (no USART -> would queue forever).
End-to-end verified: i8080-banner-streamer now prints the boot banner
followed by "uptime ticks: 0xNN" lines stepping every ~50 ms, executing
real Intel 8080 instructions inside the WASM chip.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
The hand-drawn SVGs in Bmp280Element.ts and Attiny85Element.ts were
functional but obviously amateur next to a real Fritzing-drawn part.
Both components now mount the equivalent Fritzing breadboard SVG as a
public static asset (`<image href>` in the shadow DOM SVG), with pin
coordinates remapped to the new artwork and pin-name labels overlaid
on top so the user can still read each connector at a glance.
frontend/public/component-svgs/bmp280.svg (new)
Verbatim copy of third-party/fritzing-parts/svg/core/breadboard/
bmp180_breadboard.svg. The Adafruit BMP180 breakout is the
mechanically identical Bosch predecessor — same I2C interface,
same 4-pin pinout. Pin labels lifted from the matching .fzp.
frontend/public/component-svgs/attiny85.svg (new)
Verbatim copy of the Fritzing ATtiny85 DIP-8 breadboard art.
Bmp280Element.ts
Width 80×100 px (Fritzing aspect 28.35:35.43 ≈ 0.8:1, exact uniform
scale of 2.822 px/mm). Pin coords for SDA / SCL / GND / VCC matched
to the connector centres in the source SVG. Pin labels overlaid on
top. Existing wired example (esp32-bmp280) re-routes automatically
because the wire system reads coords by pin name from pinInfo.
Attiny85Element.ts
Width 160×132 px (Fritzing aspect 28.801:23.768 ≈ 1.21:1, exact
uniform scale of 5.555 px/mm). The Fritzing layout puts pins on the
TOP and BOTTOM edges (4 each), not LEFT and RIGHT like the older
hand-drawn version. Pin coords land on clean numbers
(x ∈ {20, 60, 100, 140}, y ∈ {6, 126}). Built-in LED on PB1 stays
as an overlaid circle outside the chip body.
Wires in the existing attiny85-* examples re-route automatically by
pin name; external components positioned to the right of the chip
may need a manual nudge for clean routing — but they work.
frontend/src/components/simulator/BoardOnCanvas.tsx
attiny85: { w: 160, h: 100 } → { w: 160, h: 132 } to match the new
aspect ratio. Same width as before so the chip occupies the same
horizontal slot in existing example layouts.
scripts/component-overrides.json
BMP280 thumbnail updated to mirror the Fritzing colour scheme
(dark blue PCB, BMP180 silkscreen, four gold connector circles)
so picker and canvas feel consistent.
frontend/public/components-metadata.json
Regenerated.
docs/THIRD_PARTY.md
New "Fritzing parts library" section. Both new assets are listed
with their upstream paths plus the CC-BY-SA licence and link to
the parts repo. Future Fritzing copies must be added there too.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
David Montero Crespo