Two independent defects, both visible as "the NTC reports the wrong
temperature" (issue #233).
1. The part built its divider against a hard-coded 5 V rail, while the SPICE
path used the board's real rail. They only agreed on AVR. On a 3.3 V board
the injected node sat above the ADC's full scale: the slider at 25 C read
~1.4 C, and every slider value below ~11 C saturated to the same number, so
-40, 0 and 10 C were indistinguishable. The rail now comes from the board
(analogRailVolts), matching setAdcVoltage's own AVR/RP2040/ESP32 split.
2. The divider convention was corrected in 608c2538 (VCC -> R_pull -> OUT ->
R_NTC -> GND) but data/examples.ts was not updated with it, so three of the
four bundled NTC sketches still decoded the OTHER topology. Their readings
came out mirrored about 25 C: the uno-ntc example printed -3.42 C with the
slider at 60 C - the exact symptom dd22bcfe had recorded as the bug. Fixed
in uno-ntc, pico-ntc and attiny85-ntc-sensor; examples-circuits.ts was
already right.
The sibling analog sensors (gas, flame, heart-beat, sound) map their sliders
0..1023 onto the same hard-coded 5 V and will saturate the same way on 3.3 V
boards. Left alone here: that is not what #233 reports, and each one needs its
examples re-checked before changing.
Three generic seams, none naming any board:
The pin tracer gains a socket hop: a component that declares boardSocket
with a board actually seated on it resolves a pad to the SAME-NAMED pin
of that board — seating IS the connection, like a XIAO pushed into a
shield header or a HAT on the 40-pin. Until now a seated shield's
buttons and LEDs were dead unless the user drew wires the real stack
does not have. Wires keep working exactly as before for every other
host (Uno, Mega, Pi, STM32, ...).
setMicrophoneSource now RETURNS whether a bridge actually took the
source, so a part can state that this host has no I2S instead of
pretending to stream into a void — capability reported, never invented.
createNeopixelDecoder is exported: boards are not the only things
carrying an addressable LED, and a part with one on board needs the
same decode rather than a drifting copy.
The NTC breakout's SPICE topology was inverted relative to the example
sketch's decode formula (rNtc = R_PULL * v / (5 - v)), which assumes a 10k
pull-up from VCC to OUT and the NTC from OUT to GND. The mapper had the NTC
on top (VCC->OUT) and the pull-down on the bottom, so the recovered
temperature ran backwards: dragging the slider to 100C made the sketch
print -25C. Swap the two resistors so V_OUT = 5 * Rntc / (Rntc + Rpull),
matching the sketch and the hand-built reference netlist in
spice-avr-mixed.test.ts (T=0 -> ADC 789, T=25 -> 511, T=50 -> 270).
Also replace the SensorParts linear approximation (2.5 - (t-25)*0.02) with
the same beta-model divider so the non-SPICE ADC injection decodes back to
the slider value, and drop the dead onInput path that treated the element's
value as a raw ADC count.
Reset now restores interactive sensors (temperature/lux/gas sliders) to
their configured defaults: resetBoard re-dispatches each sensor's default
into the running sim and bumps sensorResetNonce so the open
SensorControlPanel remounts and the slider snaps back. Previously a restart
left the NTC frozen at the last dragged temperature.
Updated the examples netlist snapshot for the swapped NTC cards.
The stepper-motor and biaxial-stepper parts only decoded a one-hot wave-drive coil sequence, so they never rotated under the common two-phase full-step / Stepper.h / AccelStepper drive that Wokwi's own examples use -- only the servo moved. Rewrote both decoders to track the net magnetic-field vector of the coils (atan2 of the H-bridge currents), so the rotor follows wave, two-phase full-step and half-step drive alike, whether driven directly from GPIO or through a driver's outputs.
Also adds an A4988 STEP/DIR stepper driver (parity with Wokwi's wokwi-a4988): velxio-a4988 element renders the real Pololu A4988 Fritzing breadboard SVG (public/components/a4988.svg); MotorDriverParts.ts finds the wired stepper via the netlist and advances it one (micro)step per STEP rising edge in the DIR direction (MS1-3 microstep + active-low ENABLE). Metadata in component-overrides.json. Three examples (Uno/ESP32/Pico) wire MCU STEP/DIR -> A4988 -> stepper, coil map aligned to Wokwi (1A->B+,1B->B-,2A->A+,2B->A-).
Verified in-browser: motor rotates on Arduino Uno (avr8js) and Raspberry Pi Pico (rp2040js). tsc --noEmit clean.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The SPICE emitter already reads properties.lux (default 500, 100 nA/lux)
but the UI had no way to set it — the static dialog rejected the "range"
control type and there was no entry in SENSOR_CONTROLS for the live panel.
- Add photodiode entry in SENSOR_CONTROLS (slider 0-1000 lux)
- Register a minimal PartSimulationRegistry handler that forwards slider
values via emitPropertyChange so the netlist memo invalidates
- Switch the photodiode lux control from "range" to "number" so the
static ComponentPropertyDialog renders an editable input
- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
- Replaced syncStoreProperty function with emitPropertyChange to decouple parts from Zustand store.
- Updated relay component mapping to ensure proper handling of coil and contact states.
- Added new test cases for half-wave rectifier and relay-controlled LED to ensure correct functionality.
- Introduced InlineComponentSVGs for schematic-style icons of various components.
- Updated submodule references for qemu-lcgamboa, rp2040js, and wokwi-elements to indicate dirty state.
- Implement `ammeter-waveform.test.ts` to validate AC readings from a sine wave source.
- Create `capacitor-charge-transient.test.ts` to test the charging response of an RC circuit driven by a microcontroller pin.
- Introduce `esp32-rectifier-integration.test.ts` for testing rectifier behavior using QEMU and ESP32.
- Add helper functions in `esp32RectifierE2E.ts` for the rectifier test harness.
- Develop `voltmeter-waveform.test.ts` to ensure correct AC and DC readings from a sine wave source.
- Implement unit tests for waveform statistics in `waveform-stats.test.ts` to validate RMS, mean, peak, and interpolation functions.
- Create `waveformStats.ts` to provide statistical functions for time-domain waveform analysis.
- Implemented SensorControlPanel component to allow real-time adjustments of sensor values during simulation.
- Introduced SensorUpdateRegistry for communication between UI and simulation.
- Added configuration for various sensors including sliders and buttons for user interaction.
- Enhanced existing sensor parts to support updates from SensorControlPanel.
- Created CSS styles for the SensorControlPanel layout and controls.
- Added LogicGateParts.ts for simulating various logic gates (AND, NAND, OR, NOR, XOR, NOT).
- Introduced ProtocolParts.ts for simulating I2C and SPI components including SSD1306 OLED, DS1307 RTC, MPU6050 IMU, DHT22 sensor, HX711 load cell, IR receiver, IR remote, and MicroSD card.
- Implemented BasicParts.ts with a membrane keypad and rotary dialer simulations.
- Enhanced SensorParts.ts with a single NeoPixel and PIR motion sensor.
- Updated index.ts to include new parts for logic gates and protocols.
- Modified vite-env.d.ts to declare new custom elements for the added components.
- Introduced new SensorParts.ts to handle various sensors including tilt switch, temperature sensor, gas sensor, flame sensor, heart beat sensor, and sound sensors.
- Implemented stepper motor simulation with full-step decoding.
- Added utility functions for ADC voltage injection in partUtils.ts, supporting both AVR and RP2040.
- Updated BasicParts.ts to avoid re-registering the 7-segment display.
- Enhanced ComplexParts.ts by removing unused ADC helper functions.
- Updated index.ts to include the new SensorParts module.
- Updated Vite environment definitions to include new custom elements for sensors and stepper motors.
David Montero Crespo