Registers test_esp32_spice_photodiode.mjs (added in the previous commit)
in the ESP32 + ngspice section of the backend e2e workflow, with a 150s
timeout to accommodate ESP32 firmware compile + QEMU boot.
Adds three new test steps to backend-e2e-tests.yml:
- ngspice smoke test (standalone, no backend needed)
- ESP32 voltage divider co-simulation (compile + QEMU + ngspice ADC injection)
- ESP32 Wheatstone bridge co-simulation (NTC temperature sweep)
These run alongside the existing DHT22/HC-SR04/MPU6050/MicroPython tests
using the same QEMU .so libraries and ESP32 Arduino core 2.0.17.
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Adds 44 SPICE mappers, 58 custom metadata entries, and 12 visual
Web Components covering logic gates, transistors, op-amps, regulators,
sources, electromechanical parts and integrated-circuit packaging.
Fase 9 — component catalog expansion
------------------------------------
- 7 logic gates (AND/OR/NAND/NOR/XOR/XNOR + NOT) as SPICE B-sources
- 8 multi-input gates (AND/OR/NAND/NOR with 3 and 4 inputs)
- 9 transistors: 5 BJTs (incl. PNP 2N3906/BC557) + 4 MOSFETs (incl.
P-channel IRF9540/FQP27P06). NMOS refactored from Level=3 W=0.1
(hangs ngspice) to Level=1 with sane W/L
- 5 op-amps: LM358, LM741, TL072, LM324 with per-chip saturation
rails + opamp-ideal
- 4 linear regulators (7805, 7812, 7905, LM317) with dropout
- 3 batteries (9V, AA, coin-cell) with realistic ESR
- Signal generator (sine / square / DC)
- 2 Schottky diodes (1N5817, 1N5819) + photodiode (lux-driven
current source)
Fase 10 — electromechanical + ICs
---------------------------------
- Relay (SPDT): coil + L + S-switch with native hysteresis +
flyback diode, inverted-control trick for the NC contact
- Optocouplers 4N25 and PC817 (LED + CCCS with CTR=0.5 / 1.0)
- 7 74HC ICs as DIP-14 packages emitting 4 or 6 B-sources per
component (first mapper pattern emitting multiple device cards)
- 3 flip-flops (D, T, JK) — digital-sim only (edge detection is
not representable in ngspice .op)
- L293D dual H-bridge motor driver
Infrastructure
--------------
- scripts/component-overrides.json gains a _customComponents[] array
that lets new Velxio-only parts survive metadata regeneration
(previously applyOverrides() could only patch wokwi-elements
components that had already been scanned)
- scripts/generate-component-metadata.ts injects custom entries
before the patch loop
- New ComponentCategory values: 'logic', 'analog', 'electromech'
- frontend/src/components/DynamicComponent.tsx PASSIVE tracing
extended from just ['resistor','resistor-us'] to 9 two-terminal
passives with per-part pin name maps
- New CI workflow test-circuit.yml runs the sandbox on push/PR
- frontend-tests.yml regenerates metadata and fails if committed
JSON is stale
- Documented 2 new ngspice gotchas in circuit-emulation-gotchas.md:
unicode in netlist titles silently hangs the parser, and
MOSFET Level=3 + W=0.1m causes .op to hang
- 164/164 sandbox tests passing in ~9 s (was 88 pre-fase-9)
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
- Implemented a comprehensive test script (test_micropython_pico.mjs) that performs the following:
- Part 1: Checks backend compilation of a simple Arduino sketch for the rp2040:rp2040:rpipico board.
- Part 2: Downloads MicroPython v1.20.0 UF2 firmware and loads it into a rp2040js simulator.
- Part 3: Simulates the Pico, verifies REPL output, and checks execution of injected Python code.
- Includes detailed logging and error handling for each step of the process.
- Implement tests for BMP280, DS1307, DS3231, I2CWriteSink, and MPU6050 slaves in test_i2c_slaves.py.
- Create test suite for Velxio MCP server tools in test_mcp_tools.py, covering Wokwi utilities and circuit management functions.
- Add tests for parsing WiFi and BLE serial output in test_wifi_status_parser.py, ensuring correct status events are captured.
Docker multi-arch:
- Dockerfile downloads arch-specific QEMU .so via TARGETARCH
- docker-publish.yml adds setup-qemu-action and platforms: linux/amd64,linux/arm64
- qemu-lcgamboa submodule updated (matrix build for both architectures)
LED fix:
- LEDs now require cathode wired to GND (or LOW GPIO) to light up
- Previously LEDs turned on with anode HIGH regardless of cathode connection
- Updated tests to verify anode+cathode behavior
This workflow sends a notification to Discord whenever a new issue is opened on GitHub. It includes the issue details such as title, URL, body, user, and labels.
- Add LoginPage and RegisterPage for user authentication.
- Create UserProfilePage to display user projects.
- Implement ProjectPage for viewing and editing individual projects.
- Introduce authService for handling user login, registration, and session management.
- Add projectService for managing project data retrieval and manipulation.
- Enhance EditorPage with file management capabilities and save prompts.
- Introduce Zustand stores for managing authentication, editor state, and project state.
- Add reserved usernames utility to prevent certain usernames during registration.
- Update compilation service to handle multiple files for Arduino sketches.
davidmonterocrespo24