The SSD1306 was three picker entries — a generic `ssd1306` with a protocol
selector plus `ssd1306-i2c` / `ssd1306-spi` shortcuts (issue #101) — all the
same 8-pin wokwi-ssd1306 element. That is confusing for one physical module
(issue #215). Wokwi ships a single I2C-only part; this goes one better: a
single part that auto-detects the protocol from the wiring, like a real
breadboard — CS or DC wired to a GPIO means SPI, otherwise I2C. No protocol
switch to set, just wire it up.
Works on every board with an I2C/SPI bus (AVR, RP2040, ESP32 Xtensa, STM32).
The ssd1306-i2c / ssd1306-spi ids stay as backward-compat simulation aliases
for projects saved before the merge, but are removed from the picker. Adds an
i2cAddress property (0x3c/0x3d) matching the real module and Wokwi.
Note: ESP32-C3, Raspberry Pi 3 and the bare RISC-V board do not emulate I2C/SPI
peripherals, so no I2C/SPI device (this or any other) attaches there yet.
Add a working microSD card part backed by a FAT16 image, following the
Wokwi storage model: the project's own workspace files are auto-copied
onto the card (free), and an optional "SD Card" panel uploads extra
files (gated as a paid feature by the velxio.dev overlay; OSS default
allows it).
Frontend (in-browser AVR / RP2040):
- ProtocolParts.ts: rewrite the microsd-card part from a handshake stub
into a real SD-over-SPI device (reply-first Ncr timing, SDSC byte
addressing, single/multi-block read+write, CSD/CID, full CMD set).
- utils/fatImage.ts: dependency-free FAT16 super-floppy builder (8.3 + LFN).
- utils/sdCardFiles.ts: assemble the card image from workspace files plus
uploaded files; base64 helpers.
- components/simulator/SdCardPanel.tsx + ComponentPropertyDialog: upload UI.
- DynamicComponent + useSimulatorStore: build and inject the image on run.
- lib/proSdCardGate.ts: overlay-installable gate for the upload action.
- data/examples-storage-microsd.ts: Arduino Uno + ESP32 gallery examples.
Backend (ESP32 via QEMU):
- services/esp32_sd_slave.py: synchronous SD-over-SPI slave (Python port of
the browser part) with a sparse backing store, idle-state R1 tracking and
real CRC16 on data blocks when the host enables CRC (CMD59) -- both
required by ESP-IDF's sdspi driver.
- esp32_worker.py: route SPI bytes to the slave (returns MISO synchronously)
and feed write-only bulk transfers.
- esp32_lib_manager.py + routes/simulation.py: forward the FAT image
(sd_card.image_b64) from the start config into the worker.
Tested:
- frontend: protocol-parts, fat-image, sd-card-gate and microsd-real-firmware
(real Arduino SD.h on avr8js) -- 86 passing.
- backend: test_esp32_sd_slave (10) covering the ESP-IDF init sequence and
CRC16; validated end to end by running a real SD.h sketch in libqemu-xtensa
(mount, directory listing, read and write-readback).
- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
- Introduced I2C_SENSOR_MAP for pre-registering I2C sensors in the simulator store.
- Implemented I2C slave state machines for MPU6050, BMP280, DS1307, and DS3231 sensors in esp32_i2c_slaves.py.
- Added unit tests for I2C slave functionality covering BMP280, DS1307, DS3231, and I2CWriteSink.
- Updated the simulator store to handle I2C address resolution and sensor data management.
- Marked submodules as dirty in wokwi-libs for rp2040js and wokwi-elements.
- Added LogicGateParts.ts for simulating various logic gates (AND, NAND, OR, NOR, XOR, NOT).
- Introduced ProtocolParts.ts for simulating I2C and SPI components including SSD1306 OLED, DS1307 RTC, MPU6050 IMU, DHT22 sensor, HX711 load cell, IR receiver, IR remote, and MicroSD card.
- Implemented BasicParts.ts with a membrane keypad and rotary dialer simulations.
- Enhanced SensorParts.ts with a single NeoPixel and PIR motion sensor.
- Updated index.ts to include new parts for logic gates and protocols.
- Modified vite-env.d.ts to declare new custom elements for the added components.
David Montero