- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
Adds 44 SPICE mappers, 58 custom metadata entries, and 12 visual
Web Components covering logic gates, transistors, op-amps, regulators,
sources, electromechanical parts and integrated-circuit packaging.
Fase 9 — component catalog expansion
------------------------------------
- 7 logic gates (AND/OR/NAND/NOR/XOR/XNOR + NOT) as SPICE B-sources
- 8 multi-input gates (AND/OR/NAND/NOR with 3 and 4 inputs)
- 9 transistors: 5 BJTs (incl. PNP 2N3906/BC557) + 4 MOSFETs (incl.
P-channel IRF9540/FQP27P06). NMOS refactored from Level=3 W=0.1
(hangs ngspice) to Level=1 with sane W/L
- 5 op-amps: LM358, LM741, TL072, LM324 with per-chip saturation
rails + opamp-ideal
- 4 linear regulators (7805, 7812, 7905, LM317) with dropout
- 3 batteries (9V, AA, coin-cell) with realistic ESR
- Signal generator (sine / square / DC)
- 2 Schottky diodes (1N5817, 1N5819) + photodiode (lux-driven
current source)
Fase 10 — electromechanical + ICs
---------------------------------
- Relay (SPDT): coil + L + S-switch with native hysteresis +
flyback diode, inverted-control trick for the NC contact
- Optocouplers 4N25 and PC817 (LED + CCCS with CTR=0.5 / 1.0)
- 7 74HC ICs as DIP-14 packages emitting 4 or 6 B-sources per
component (first mapper pattern emitting multiple device cards)
- 3 flip-flops (D, T, JK) — digital-sim only (edge detection is
not representable in ngspice .op)
- L293D dual H-bridge motor driver
Infrastructure
--------------
- scripts/component-overrides.json gains a _customComponents[] array
that lets new Velxio-only parts survive metadata regeneration
(previously applyOverrides() could only patch wokwi-elements
components that had already been scanned)
- scripts/generate-component-metadata.ts injects custom entries
before the patch loop
- New ComponentCategory values: 'logic', 'analog', 'electromech'
- frontend/src/components/DynamicComponent.tsx PASSIVE tracing
extended from just ['resistor','resistor-us'] to 9 two-terminal
passives with per-part pin name maps
- New CI workflow test-circuit.yml runs the sandbox on push/PR
- frontend-tests.yml regenerates metadata and fails if committed
JSON is stale
- Documented 2 new ngspice gotchas in circuit-emulation-gotchas.md:
unicode in netlist titles silently hangs the parser, and
MOSFET Level=3 + W=0.1m causes .op to hang
- 164/164 sandbox tests passing in ~9 s (was 88 pre-fase-9)
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
- Added LogicGateParts.ts for simulating various logic gates (AND, NAND, OR, NOR, XOR, NOT).
- Introduced ProtocolParts.ts for simulating I2C and SPI components including SSD1306 OLED, DS1307 RTC, MPU6050 IMU, DHT22 sensor, HX711 load cell, IR receiver, IR remote, and MicroSD card.
- Implemented BasicParts.ts with a membrane keypad and rotary dialer simulations.
- Enhanced SensorParts.ts with a single NeoPixel and PIR motion sensor.
- Updated index.ts to include new parts for logic gates and protocols.
- Modified vite-env.d.ts to declare new custom elements for the added components.
- Introduced new SensorParts.ts to handle various sensors including tilt switch, temperature sensor, gas sensor, flame sensor, heart beat sensor, and sound sensors.
- Implemented stepper motor simulation with full-step decoding.
- Added utility functions for ADC voltage injection in partUtils.ts, supporting both AVR and RP2040.
- Updated BasicParts.ts to avoid re-registering the 7-segment display.
- Enhanced ComplexParts.ts by removing unused ADC helper functions.
- Updated index.ts to include the new SensorParts module.
- Updated Vite environment definitions to include new custom elements for sensors and stepper motors.
- Added SimulatorCanvas component for rendering the simulator interface.
- Integrated Wokwi components (Arduino, LED, Resistor, Pushbutton, Potentiometer) into the simulator.
- Created PinManager to handle pin state changes and notifications.
- Developed AVRSimulator class for emulating Arduino Uno functionality.
- Implemented hex file loading and compilation service.
- Added CSS styles for the simulator interface.
- Established Zustand stores for managing editor and simulator states.
- Created utility functions for parsing Intel HEX format.
- Set up Vite configuration for the frontend project.
- Added batch scripts for starting backend and frontend servers, and updating Wokwi libraries.
David Montero Crespo