- Implemented handshake tests to validate initial bus state and register responses.
- Created end-to-end tests for Pico W LED blinking using MicroPython firmware.
- Added SDPCM framing tests to ensure proper encoding and decoding of control frames.
- Developed IOCTL tests to verify command responses and state changes in the emulator.
- Established a full lifecycle test for WiFi operations, including scanning, connecting, and packet handling.
- Introduced TypeScript configuration for test files to ensure compatibility and strict type checking.
Fixes the user-reported bug where two RPi Pico W boards wired GP0↔GP1
running SerialPassthrough don't communicate. Replaces the broken
broadcast-style cross-board logic in addBoard (only routed AVR↔Pi3B,
ignored wires entirely, no RP2040↔anything path) with a wire-aware
Interconnect singleton.
Architecture: digital pin transitions are the lowest-common-denominator
abstraction. Each simulator's hardware peripherals (UART/I2C/SPI) and
bit-banging libraries (SoftwareSerial, software I2C) decode the
transitions naturally — propagate the pin and the protocols come for
free. For cross-process boards (ESP32 backend QEMU, Pi3B QEMU) a
byte-level shortcut is additionally enabled on hardware-UART pin
pairs to handle high-baud links over WebSocket latency.
Implementation:
- New simulation/Interconnect.ts singleton subscribes to wire/board
changes via the Zustand store. Handlers per tier: browser-sim →
pinManager.onPinChange, ESP32 → Esp32Bridge.sendPinEvent, Pi3B →
bridge.sendPinEvent. Re-entrancy guard via per-(board,pin) Set.
- New utils/boardProtocols.ts classifies pins (uart-tx, i2c-sda, etc.)
per board kind, used as optimization hint for the byte shortcut.
- types/wire.ts: added signalType field, exports WireSignalType /
WireColorMap (fixes a pre-existing TS import error in wireColors).
- Deleted the bridgeMap/simulatorMap broadcast forEach blocks in
addBoard. Initial board + future boards register with Interconnect
via setInterconnectRuntime + store subscription.
- PinManager.resetPinStates() helper for test isolation.
Tests (16 new files, 96 tests, all passing):
- Per-pair × per-protocol matrix: dual-arduino-digital,
dual-pico-digital, arduino-pico-digital, triple-pico-digital-chain,
dual-arduino-hw-uart, dual-arduino-software-serial,
arduino-pico-mixed-uart, arduino-esp32-uart, dual-esp32-uart,
pi3-pico-uart, arduino-pico-i2c, arduino-arduino-spi,
interconnect-routing, dual-arduino-multi-protocol (UART+I2C+SPI+
digital + concurrent), dual-pico-multi-protocol (UART0+UART1 alt+
I2C0+I2C1+SPI0+digital + 3-Pico star topology)
- Updated dual-pico-serial-passthrough to assert correct behaviour
- Backend test/multi_board_esp32/test_dual_esp32_serial.py for two
real QEMU instances (skip-graceful when lcgamboa lib absent)
Verified: 1107/1107 tests pass, zero regressions, vite build OK.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
- Implemented a script to inject passive-component preset variants into `scripts/component-overrides.json`, including resistors, capacitors, and inductors with custom names and thumbnails.
- Added a new custom element `<wokwi-capacitor-electrolytic>` representing a polarized aluminum-can capacitor with appropriate SVG representation.
- Updated metadata generation to accommodate new component names and thumbnails for better user experience in the component picker.
- Marked submodules `qemu-lcgamboa` and `rp2040js` as dirty to reflect local changes.
- Replaced syncStoreProperty function with emitPropertyChange to decouple parts from Zustand store.
- Updated relay component mapping to ensure proper handling of coil and contact states.
- Added new test cases for half-wave rectifier and relay-controlled LED to ensure correct functionality.
- Introduced InlineComponentSVGs for schematic-style icons of various components.
- Updated submodule references for qemu-lcgamboa, rp2040js, and wokwi-elements to indicate dirty state.
- Implement `ammeter-waveform.test.ts` to validate AC readings from a sine wave source.
- Create `capacitor-charge-transient.test.ts` to test the charging response of an RC circuit driven by a microcontroller pin.
- Introduce `esp32-rectifier-integration.test.ts` for testing rectifier behavior using QEMU and ESP32.
- Add helper functions in `esp32RectifierE2E.ts` for the rectifier test harness.
- Develop `voltmeter-waveform.test.ts` to ensure correct AC and DC readings from a sine wave source.
- Implement unit tests for waveform statistics in `waveform-stats.test.ts` to validate RMS, mean, peak, and interpolation functions.
- Create `waveformStats.ts` to provide statistical functions for time-domain waveform analysis.
- Implement `serial-batching.test.ts` to verify the behavior of `createSerialBatcher`, ensuring it coalesces multiple appends into a single flush, preserves byte order, and groups by board.
- Create `spice-rectifier-integration.test.ts` to test the end-to-end functionality of the Half-Wave Rectifier example, covering the entire simulation pipeline from input building to circuit solving.
- Add `spice-rectifier-live-repro.test.ts` to reproduce a live-app failure scenario, tracing through each layer of the simulation to identify potential failure points.
- Introduce `spice-signal-generator-tran.test.ts` to validate the behavior of the signal generator and ensure correct analysis type switching based on circuit components.
- Establish `serialBatcher.ts` to implement a batching mechanism for USART output, reducing the frequency of store updates and preventing React's maximum update depth error.
- Decoupled electrical simulation from the simulator store, ensuring SPICE is always active for accurate circuit analysis.
- Removed feature flag for electrical simulation, simplifying the state management.
- Preloaded SPICE engine at app start to eliminate latency during the first solve.
- Added comprehensive tests for MOSFET PWM LED behavior and NPN transistor switch functionality, ensuring correct current flow and response to pin states.
- Implemented diagnostics for floating input nodes in RC low-pass filter circuits, addressing singular matrix issues in SPICE simulations.
- Introduced active semiconductor metadata registry for better component management and simulation fidelity.
- Updated Vite configuration to force re-bundling of local wokwi-elements after component additions.
fix: increase timeout for compilation requests to 180 seconds
refactor: call recalculateAllWirePositions after loading examples
chore: update subproject commit for rp2040js to dirty state
chore: update subproject commit for wokwi-elements to dirty state
Previously examples.ts pushed to exampleProjects[] after declaration, which
some bundlers can treat as dead code under aggressive tree-shaking. This
also made HMR unreliable when examples-circuits.ts changed.
Now:
const legacyExamples = [...]
export const exampleProjects = [...legacyExamples, ...circuitExamples]
Single immutable export. Guaranteed to include all 150 examples at import
time. The gallery (ExamplesGallery.tsx) and SSR prerender (entry-server.tsx)
both pick up the new circuit examples automatically.
Also adds frontend/src/__tests__/examples-circuits.test.ts with 5 assertions
to catch future regressions (all circuit ids present, no duplicates, valid
required fields, expected categories covered).
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
Adds 44 SPICE mappers, 58 custom metadata entries, and 12 visual
Web Components covering logic gates, transistors, op-amps, regulators,
sources, electromechanical parts and integrated-circuit packaging.
Fase 9 — component catalog expansion
------------------------------------
- 7 logic gates (AND/OR/NAND/NOR/XOR/XNOR + NOT) as SPICE B-sources
- 8 multi-input gates (AND/OR/NAND/NOR with 3 and 4 inputs)
- 9 transistors: 5 BJTs (incl. PNP 2N3906/BC557) + 4 MOSFETs (incl.
P-channel IRF9540/FQP27P06). NMOS refactored from Level=3 W=0.1
(hangs ngspice) to Level=1 with sane W/L
- 5 op-amps: LM358, LM741, TL072, LM324 with per-chip saturation
rails + opamp-ideal
- 4 linear regulators (7805, 7812, 7905, LM317) with dropout
- 3 batteries (9V, AA, coin-cell) with realistic ESR
- Signal generator (sine / square / DC)
- 2 Schottky diodes (1N5817, 1N5819) + photodiode (lux-driven
current source)
Fase 10 — electromechanical + ICs
---------------------------------
- Relay (SPDT): coil + L + S-switch with native hysteresis +
flyback diode, inverted-control trick for the NC contact
- Optocouplers 4N25 and PC817 (LED + CCCS with CTR=0.5 / 1.0)
- 7 74HC ICs as DIP-14 packages emitting 4 or 6 B-sources per
component (first mapper pattern emitting multiple device cards)
- 3 flip-flops (D, T, JK) — digital-sim only (edge detection is
not representable in ngspice .op)
- L293D dual H-bridge motor driver
Infrastructure
--------------
- scripts/component-overrides.json gains a _customComponents[] array
that lets new Velxio-only parts survive metadata regeneration
(previously applyOverrides() could only patch wokwi-elements
components that had already been scanned)
- scripts/generate-component-metadata.ts injects custom entries
before the patch loop
- New ComponentCategory values: 'logic', 'analog', 'electromech'
- frontend/src/components/DynamicComponent.tsx PASSIVE tracing
extended from just ['resistor','resistor-us'] to 9 two-terminal
passives with per-part pin name maps
- New CI workflow test-circuit.yml runs the sandbox on push/PR
- frontend-tests.yml regenerates metadata and fails if committed
JSON is stale
- Documented 2 new ngspice gotchas in circuit-emulation-gotchas.md:
unicode in netlist titles silently hangs the parser, and
MOSFET Level=3 + W=0.1m causes .op to hang
- 164/164 sandbox tests passing in ~9 s (was 88 pre-fase-9)
Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
- Implemented Bmp280Element as a custom web component for the BMP280 barometric sensor, including SVG representation and pin configuration.
- Created CircuitPreview component to render circuit thumbnails using SVGs of components, including support for various boards and components.
- Added a script to generate SVG files from wokwi-elements, ensuring proper formatting and structure for reliable rendering.
- Introduced a test HTML generation script to visualize component SVGs.
- Introduced I2C_SENSOR_MAP for pre-registering I2C sensors in the simulator store.
- Implemented I2C slave state machines for MPU6050, BMP280, DS1307, and DS3231 sensors in esp32_i2c_slaves.py.
- Added unit tests for I2C slave functionality covering BMP280, DS1307, DS3231, and I2CWriteSink.
- Updated the simulator store to handle I2C address resolution and sensor data management.
- Marked submodules as dirty in wokwi-libs for rp2040js and wokwi-elements.
Docker multi-arch:
- Dockerfile downloads arch-specific QEMU .so via TARGETARCH
- docker-publish.yml adds setup-qemu-action and platforms: linux/amd64,linux/arm64
- qemu-lcgamboa submodule updated (matrix build for both architectures)
LED fix:
- LEDs now require cathode wired to GND (or LOW GPIO) to light up
- Previously LEDs turned on with anode HIGH regardless of cathode connection
- Updated tests to verify anode+cathode behavior
Replace arduino-cli with ESP-IDF 4.4.7 for ESP32 compilation — Arduino-compiled
firmware crashes in QEMU (9-28 reboots) while ESP-IDF boots cleanly (0 reboots).
The new espidf_compiler translates Arduino WiFi/WebServer sketches to native
ESP-IDF C code, compiles with cmake+ninja, and merges into 4MB flash images.
Key changes:
- ESP-IDF compiler: translates WiFi.begin/WebServer to esp_wifi/esp_http_server
- ESP-IDF project template with QEMU-optimized sdkconfig (DIO, 40MHz, no WDT)
- WiFi status parser for ESP-IDF serial logs (wifi_status, ble_status events)
- IoT Gateway HTTP reverse proxy for ESP32 web servers
- WiFi/BLE auto-detection from sketch content + visual status icons
- Static IP 192.168.4.15 matching slirp DHCP first-client range
- Docker: new espidf-builder stage with ESP-IDF 4.4.7 toolchain
- 157 tests covering WiFi/BLE for both ESP32 (Xtensa) and ESP32-C3 (RISC-V)
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
fix: improve session ID handling in Esp32Bridge and update WebSocket close logging
chore: mark subprojects as dirty in QEMU, RP2040, and Wokwi elements libraries
- Added board-agnostic sensor registration methods in RP2040Simulator.
- Enhanced ComplexParts to handle LEDC PWM duty updates for ESP32.
- Updated ProtocolParts to check if the simulator handles sensor protocols natively, delegating to backend if applicable.
- Introduced pre-registration of sensors in useSimulatorStore for ESP32 to prevent race conditions.
- Added tests for ESP32 DHT22 sensor registration flow, ensuring proper delegation and fallback mechanisms.
- Created tests for ESP32 Servo and Potentiometer interactions, verifying PWM subscriptions and ADC handling.
- Implemented SensorControlPanel component to allow real-time adjustments of sensor values during simulation.
- Introduced SensorUpdateRegistry for communication between UI and simulation.
- Added configuration for various sensors including sliders and buttons for user interaction.
- Enhanced existing sensor parts to support updates from SensorControlPanel.
- Created CSS styles for the SensorControlPanel layout and controls.
- Implemented a simple LED blink program in C for the ESP32-C3, targeting RV32IMC architecture.
- Created a linker script to define memory layout for the ESP32-C3.
- Added build script to compile the blink program using the riscv32-esp-elf-gcc toolchain.
- Developed Esp32C3Simulator to emulate ESP32-C3 behavior in the browser, including GPIO and UART functionality.
- Implemented utility functions to parse ESP32 flash images and handle loading of binary data.
- Included disassembly output for debugging purposes.
- Added necessary test fixtures for the blink example.
- Introduced ArduinoMega component for rendering in the simulator.
- Updated SimulatorCanvas to handle Arduino Mega board type.
- Enhanced AVRSimulator to support ATmega2560 architecture, including PWM pin mapping and port management.
- Modified PinManager to accommodate Mega's non-linear pin mapping.
- Updated boardPinMapping utility to include Mega analog pins.
- Adjusted Wokwi import/export functionality to recognize and handle Arduino Mega.
- Updated useSimulatorStore to initialize AVRSimulator with the correct board variant.
- Added LogicGateParts.ts for simulating various logic gates (AND, NAND, OR, NOR, XOR, NOT).
- Introduced ProtocolParts.ts for simulating I2C and SPI components including SSD1306 OLED, DS1307 RTC, MPU6050 IMU, DHT22 sensor, HX711 load cell, IR receiver, IR remote, and MicroSD card.
- Implemented BasicParts.ts with a membrane keypad and rotary dialer simulations.
- Enhanced SensorParts.ts with a single NeoPixel and PIR motion sensor.
- Updated index.ts to include new parts for logic gates and protocols.
- Modified vite-env.d.ts to declare new custom elements for the added components.
- Introduced new SensorParts.ts to handle various sensors including tilt switch, temperature sensor, gas sensor, flame sensor, heart beat sensor, and sound sensors.
- Implemented stepper motor simulation with full-step decoding.
- Added utility functions for ADC voltage injection in partUtils.ts, supporting both AVR and RP2040.
- Updated BasicParts.ts to avoid re-registering the 7-segment display.
- Enhanced ComplexParts.ts by removing unused ADC helper functions.
- Updated index.ts to include the new SensorParts module.
- Updated Vite environment definitions to include new custom elements for sensors and stepper motors.
- Simplified serial data handling in `useSimulatorStore` for both AVR and RP2040 simulators.
- Introduced `boardPinMapping.ts` to map wokwi-element pin names to simulator GPIO/pin numbers for Arduino Uno and Nano RP2040.
- Added `compilationLogger.ts` to parse compile results into structured log entries for better console output.
- Implemented a comprehensive backend test suite in `test_compilation.py` to validate the Arduino CLI installation, AVR core presence, compilation service, and API endpoint functionality.
- Created a frontend test suite in `simulation.test.ts` to test the `PinManager` and `AVRSimulator` components, ensuring proper functionality and integration.
- Introduced new components for wire management in the simulator, including `PinOverlay`, `WireInProgressRenderer`, `WireLayer`, and `WireRenderer`, enhancing the visual wiring system.
- Developed utility functions for pin position calculations and wire color management, ensuring accurate connections and visual representation.
- Added types for wire management in `wire.ts`, defining structures for wire endpoints, control points, and signal types.
David Montero Crespo
copilot-swe-agent[bot]