Adds `velxio-ssd1306-i2c-4pin`, a native 4-pin SSD1306 OLED module
(GND/VCC/SCL/SDA) — the cheap 0.96" I2C board most beginners actually have,
matching Wokwi's board-ssd1306. The 8-pin `wokwi-ssd1306` breakout stays; this
is the distinct 4-pin part (issue #215). Same SSD1306Core render pipeline
(imageData/redraw) so the display paints identically; I2C-only, address via the
i2cAddress property (default 0x3C). Styled after the existing 8-pin element
(blue PCB, dark screen, corner holes, star).
Ships four "SSD1306 OLED (4-pin I2C)" gallery examples wiring it over I2C on
Arduino Uno (A4/A5), ESP32 (21/22), Raspberry Pi Pico (GP4/GP5) and STM32 Blue
Pill (PB7/PB6).
The stepper-motor and biaxial-stepper parts only decoded a one-hot wave-drive coil sequence, so they never rotated under the common two-phase full-step / Stepper.h / AccelStepper drive that Wokwi's own examples use -- only the servo moved. Rewrote both decoders to track the net magnetic-field vector of the coils (atan2 of the H-bridge currents), so the rotor follows wave, two-phase full-step and half-step drive alike, whether driven directly from GPIO or through a driver's outputs.
Also adds an A4988 STEP/DIR stepper driver (parity with Wokwi's wokwi-a4988): velxio-a4988 element renders the real Pololu A4988 Fritzing breadboard SVG (public/components/a4988.svg); MotorDriverParts.ts finds the wired stepper via the netlist and advances it one (micro)step per STEP rising edge in the DIR direction (MS1-3 microstep + active-low ENABLE). Metadata in component-overrides.json. Three examples (Uno/ESP32/Pico) wire MCU STEP/DIR -> A4988 -> stepper, coil map aligned to Wokwi (1A->B+,1B->B-,2A->A+,2B->A-).
Verified in-browser: motor rotates on Arduino Uno (avr8js) and Raspberry Pi Pico (rp2040js). tsc --noEmit clean.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
useSimulatorStore eagerly imports STM32_LED from this module, so the
top-level `class extends HTMLElement` + customElements.define ran at import
time and threw "HTMLElement is not defined" under vitest's node environment,
breaking 20 test files that load the store. Guard the base class with a
dummy fallback and skip registration when customElements is absent; browser
behavior is unchanged.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
Adds stm32-f4-discovery, stm32-olimex-h405, stm32-netduino-plus2, stm32-netduino2, stm32-blackpill-f401 and stm32-bluepill-f103cb, mapped to existing qemu-lcgamboa machines (netduinoplus2, olimex-stm32-h405, netduino2, stm32vldiscovery). A generic inline board renderer (no SVG) draws the Discovery/Olimex/Netduino boards from a header pin layout; the Pill variants reuse the Blue/Black Pill SVGs. Per-board onboard-LED pin and polarity via STM32_LED. One blink+serial example per board.
tsc --noEmit clean; all new FQBN pnum variants present in STM32 core 2.12.0; worker smoke tests pass for the new machines.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
STM32 emulation (open-core, runs via libqemu-arm in the backend worker):
- backend: stm32_lib_manager + stm32_worker (GPIO, USART, I2C/SPI device models
reusing the ESP32 slaves, live sensor updates), arduino_cli STM32 branch,
start_stm32 simulation route.
- frontend: Stm32Bridge + Stm32BluePill(/BlackPill) web components (Wokwi SVGs),
board kinds, Interconnect/boardPinMapping/boardProtocols wiring, example
projects (blink, serial, I2C BMP280/MPU6050/DS1307/SSD1306/weather, 7-seg,
RGB, button, switch, stepper, cross-board interconnect).
- Raspberry Pi 4/5 board elements + thumbnails.
Pro board gating (generic OSS->Pro seam; entitlement logic lives in the overlay):
- lib/proBoardGate.ts: isProBoardKind (STM32 + every QEMU Raspberry Pi),
installBoardGateImpl/boardGateDecision, triggerProUpgradePrompt.
- PRO badge on those boards in the component picker; gate at the picker add +
the run backstop (startBoard).
- backend/app/services/board_access.py: server-side enforcement seam for the
simulation WebSocket; STM32/Pi unavailable -> Pro-framed message.
- desktop: generic QemuDownloadPrompt + Stm32QemuPrompt (download-behind-license,
mirrors the ESP32 prompt).
- .gitignore: never ship libqemu-* binaries in the public image.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
The BoardKind type and the QEMU backend already supported
raspberry-pi-4 (Cortex-A72) and raspberry-pi-5 (Cortex-A76) by reusing
the Pi 3 arm64 image set, but the frontend had no way to actually
select either: the board picker, the canvas renderer, the serial
monitor, the oscilloscope channel list, and the editor toolbar all
hard-coded "raspberry-pi-3" as the only Pi entry. ComponentRegistry
even registered Pi 4 / Pi 5 metadata pointing at the velxio-raspberry-pi-3
custom-element tag — a placeholder that meant both boards rendered as
a Pi 3 in the picker thumbnail and on the canvas.
Add dedicated boards top-to-bottom:
* `RaspberryPi4Element.ts` / `RaspberryPi5Element.ts` — Velxio-style
schematic SVG (authored from scratch, not traced). Pi 4 is the
green PCB with BCM2711 SoC, 4× USB-A, USB-C power, dual µHDMI;
Pi 5 is the darker green PCB with BCM2712 + RP1 southbridge,
2.5 GbE, USB-C 5V/5A, PCIe FFC connector, dedicated power
button. Both carry a small "velxio" mark in the corner.
* `pi40PinHeader.ts` — shared `buildPi40PinHeader()` helper that
returns the 40-pin BCM layout. Every Pi from the 1B+ onwards
uses the same physical pin positions and same BCM GPIO
assignment, so Pi 3 / Pi 4 / Pi 5 elements all consume this
helper and example wires drawn against one model transfer to
the others without re-routing.
* React wrappers `RaspberryPi4.tsx` / `RaspberryPi5.tsx` render the
custom elements at absolute positions (mirrors how
RaspberryPi3.tsx handles the Pi 3 illustration).
* Wire-up across the editor surface:
- BoardOnCanvas: BOARD_SIZE entry + switch case.
- BoardPickerModal: description, icon, kinds list.
- ComponentPickerModal: thumbnails now instantiate the dedicated
custom element (was velxio-raspberry-pi-3 fallback).
- SerialMonitor / EditorToolbar: pill labels, icons, colours.
- Oscilloscope: GPIO channel list (28 BCM pins).
- SimulatorCanvas: remote-boards filter for run/stop sync.
- SPICE boardPinGroups: same 5V / 3V3 / GND as Pi 3.
- boardPinToNumber: accepts physical pin numbers ("1"-"40"),
BCM names ("GPIO14") and power labels for any Pi 3/4/5 id.
- ComponentRegistry: dedicated tagNames + per-board thumbnails
(green for Pi 4, darker green for Pi 5).
* EditorToolbar's Pi 3 special cases (Linux/Python compile path,
Run/Stop routing) now use `isPiBoardKind()` so Pi 4 and Pi 5
inherit the same behaviour automatically, and any future Pi
family member (Zero / 1 / 2) lands in the right code paths the
moment its backend boots.
QEMU backend was already wired (qemu_manager.py:71/82 + manifest entry
'raspberry-pi-3-virt' shared across arm64 Pis), so this commit makes
both boards selectable end-to-end without any backend follow-up.
On the ESP32 DevKit V1 the silkscreen labels GPIO 16 / 17 as RX2 / TX2,
and Esp32Element.PINS_ESP32 only exposed the silkscreen names. Examples
that wire to numeric pin "16" or "17" (e.g. ledcAttach(16, 5000, 8) on
esp32-pwm-led-rgb) couldn't resolve those names — pinPositionCalculator
failed lookups, the wire endpoint fell back to (0,0)/(50,50) and the
LED component visually floated off the board, breaking the SPICE
netlist for the example.
Add "16" and "17" as aliases pointing to the same (134,143) / (134,131)
coordinates as RX2 / TX2 so both naming conventions resolve to the same
physical pin tip.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
ATtiny85 (AVRSimulator + collectPinStates + connectAnalogInputsToMcu + SimulatorCanvas + Attiny85Element + examples):
- Add attiny85AdcConfig with correct register addresses (ADMUX=0x27,
ADCSRA=0x26, ADCSRB=0x23, ADCL=0x24, ADCH=0x25, DIDR0=0x34, adcInterrupt=0x08).
Without this, analogRead() polled the wrong address forever and the
firmware hung on first ADC read.
- Add attiny85Timer0Config + instantiate AVRTimer so OVF fires at the
ATTinyCore-expected ~1.024 ms cadence. delay() advance is still blocked
on avr8js TIFR auto-clear semantics (separate upstream issue, see
ATTINY85_TIMER0_UPSTREAM_ISSUE.md in velxio-prod test plan).
- Map ATtiny85 ADC channels to PB-style pin names (PB5/PB2/PB4/PB3 -> 0..3)
in connectAnalogInputsToMcu so SPICE node voltages reach the right ADC
channel.
- Recognise /^PB\d+$/ in collectPinStates.pinNameToArduinoPin so wires
named "PB1" emit v_attiny85_pb1 V-source and the LED responds to MCU
writes. Previously every PB-wire returned -1 and SPICE saw no source.
- SimulatorCanvas: subscribe pin 1 (PB1) for the built-in LED on the
attiny85 board kind (Digispark convention), instead of falling through
to the pin-13 default.
- Attiny85Element: remove the hand-drawn "yellow LED" circle that was
floating above the chip. The bare DIP-8 has no on-board LED; examples
wire a real wokwi-led + resistor instead.
- examples.ts: add a real wokwi-led + 220 Ohm wokwi-resistor + wires to
attiny85-blink, and add missing series resistors to attiny85-button-led
and attiny85-ntc-sensor. attiny85-pwm-fade was already correct.
Custom-chip pipeline (CustomChipPart + simulatorBridges):
- Add a requestAnimationFrame loop that calls instance.tickTimers() every
frame in CustomChipPart. Chips that register vx_timer_create (e.g. an
i8080 stepping its core, or a sensor publishing samples) had timers
added to the queue but nothing fired them; tickTimers was dead code.
- Gate the ESP32 backend path with detectSimulatorKind(sim)==='esp32'.
The previous `typeof sim.registerSensor === 'function'` check matched
AVR and RP2040 simulators too (they expose registerSensor for I2C
sensor proxies), routing client-side chips to a non-existent ESP32
worker on those boards.
- Replace direct simulator.usart.writeByte calls in avrUartTx with a
JS-level FIFO + setTimeout(1ms) drainer. avr8js writeByte drops bytes
under burst load (a chip emitting print_string lost ~99% of bytes via
non-immediate, or kept only the last byte via immediate). The drainer
attempts one non-immediate write per tick and retries on RXC busy /
RXEN off. Added a guard for ATtiny85 (no USART -> would queue forever).
End-to-end verified: i8080-banner-streamer now prints the boot banner
followed by "uptime ticks: 0xNN" lines stepping every ~50 ms, executing
real Intel 8080 instructions inside the WASM chip.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
The hand-drawn SVGs in Bmp280Element.ts and Attiny85Element.ts were
functional but obviously amateur next to a real Fritzing-drawn part.
Both components now mount the equivalent Fritzing breadboard SVG as a
public static asset (`<image href>` in the shadow DOM SVG), with pin
coordinates remapped to the new artwork and pin-name labels overlaid
on top so the user can still read each connector at a glance.
frontend/public/component-svgs/bmp280.svg (new)
Verbatim copy of third-party/fritzing-parts/svg/core/breadboard/
bmp180_breadboard.svg. The Adafruit BMP180 breakout is the
mechanically identical Bosch predecessor — same I2C interface,
same 4-pin pinout. Pin labels lifted from the matching .fzp.
frontend/public/component-svgs/attiny85.svg (new)
Verbatim copy of the Fritzing ATtiny85 DIP-8 breadboard art.
Bmp280Element.ts
Width 80×100 px (Fritzing aspect 28.35:35.43 ≈ 0.8:1, exact uniform
scale of 2.822 px/mm). Pin coords for SDA / SCL / GND / VCC matched
to the connector centres in the source SVG. Pin labels overlaid on
top. Existing wired example (esp32-bmp280) re-routes automatically
because the wire system reads coords by pin name from pinInfo.
Attiny85Element.ts
Width 160×132 px (Fritzing aspect 28.801:23.768 ≈ 1.21:1, exact
uniform scale of 5.555 px/mm). The Fritzing layout puts pins on the
TOP and BOTTOM edges (4 each), not LEFT and RIGHT like the older
hand-drawn version. Pin coords land on clean numbers
(x ∈ {20, 60, 100, 140}, y ∈ {6, 126}). Built-in LED on PB1 stays
as an overlaid circle outside the chip body.
Wires in the existing attiny85-* examples re-route automatically by
pin name; external components positioned to the right of the chip
may need a manual nudge for clean routing — but they work.
frontend/src/components/simulator/BoardOnCanvas.tsx
attiny85: { w: 160, h: 100 } → { w: 160, h: 132 } to match the new
aspect ratio. Same width as before so the chip occupies the same
horizontal slot in existing example layouts.
scripts/component-overrides.json
BMP280 thumbnail updated to mirror the Fritzing colour scheme
(dark blue PCB, BMP180 silkscreen, four gold connector circles)
so picker and canvas feel consistent.
frontend/public/components-metadata.json
Regenerated.
docs/THIRD_PARTY.md
New "Fritzing parts library" section. Both new assets are listed
with their upstream paths plus the CC-BY-SA licence and link to
the parts repo. Future Fritzing copies must be added there too.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Resolves several install pain points reported by users (#108, #120) and
removes the obligatory upstream-clone step that confused contributors and
slowed down every Docker build.
Install fixes:
- nginx: server_name → catch-all default_server, drop Debian's stock site
so reverse-proxied users no longer get the "Welcome to nginx" page.
- entrypoint: auto-generate SECRET_KEY at first boot, persisted under
data/.secret_key. backend/.env is now optional in docker-compose.yml.
- backend: add greenlet>=3.0.0 (SQLAlchemy async dep that was missing on
some Python builds — caused uvicorn startup failures on WSL).
Wokwi libs come from npm:
- @wokwi/elements 1.9.2, avr8js 0.21.0, rp2040js 1.3.2 are pinned in
frontend/package.json. Vite aliases removed.
- Dockerfile.standalone no longer clones avr8js / rp2040js / wokwi-elements
/ wokwi-boards. Frontend stage is just COPY + npm install + build:docker.
- Board SVGs vendored under frontend/public/boards/ (10 deduped against
existing files, 2 truly new). third-party/wokwi-* clones become reference-
only credits — generate-component-metadata.ts skips gracefully when absent.
Production config split out:
- docker-compose.prod.yml, deploy/nginx.prod.conf, nginx-host-velxio*.conf,
update-third-party.bat removed. Production deployment lives in its own
repo: https://github.com/velxio/velxio-prod (host nginx + HTTPS + backups
+ pinned upstream commit).
Verified locally: 1161 frontend tests pass, build:docker completes clean.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
The directory grew well beyond Wokwi-only contents: it now hosts
lcgamboa's QEMU fork (qemu-lcgamboa), Espressif's esp32-camera, the
ngspice WASM build, fritzing-parts, picowi, an alternative QEMU
(qemu-esp32), the 100_Days_100_IoT_Projects examples repo, and
Wokwi's own avr8js/rp2040js/wokwi-elements/wokwi-features/wokwi-boards.
"wokwi-libs" was misleading — half the contents have nothing to do
with Wokwi. "third-party/" is the standard convention for vendored
external dependencies.
Mechanical changes:
Path rename:
wokwi-libs/ → third-party/
update-wokwi-libs.bat → update-third-party.bat
docs/WOKWI_LIBS.md → docs/THIRD_PARTY.md
Submodule reconfiguration:
.gitmodules — 4 path= and section names updated
.git/modules/wokwi-libs/ → .git/modules/third-party/
each submodule's .git file rewired to ../../.git/modules/third-party/<name>
Reference updates (~80 files): vite.config.ts aliases, Dockerfile
COPY paths, GH Actions workflow steps, build_qemu_*.sh, all
docs/* and test/*/autosearch/* entries that mention the path,
package-lock.json file: dependencies, .gitignore patterns,
sitemap.xml + index.html SEO blurbs, scripts/generate-component-*,
.dockerignore, .idea/vcs.xml. Bulk replaced both `wokwi-libs/`
(path) and bare `wokwi-libs` (textual mentions in docs/comments).
Verified:
- npx tsc -b --noEmit produces no new errors related to these paths
- vite.config.ts aliases now point at ../third-party/avr8js etc.
- All 4 git submodules (avr8js, rp2040js, wokwi-elements,
wokwi-features) are linked under third-party/ with their
worktrees re-populated and config files referencing the new path
- `grep -r wokwi-libs` returns zero hits outside node_modules,
.vite, frontend/dist, third-party/ (upstream submodule contents),
*.pyc caches, and *.dll.pre-camera rollback binaries
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
- Introduced EPaperPanels.ts to define configurations for various ePaper panels including dimensions, refresh rates, and controller details.
- Implemented SSD168xDecoder.ts to handle the decoding of SPI commands for the SSD168x family of ePaper displays.
- Created EPaperPart.ts to manage the simulation of ePaper panels, integrating with the existing simulator architecture and handling events.
- Added example sketches for 2.13", 2.9", 4.2", and 7.5" ePaper displays, demonstrating basic functionality and text rendering.
- Ensured compatibility with AVR, RP2040, and ESP32 platforms, with appropriate pin configurations for each.
- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
- Introduced RelayElements for SPDT relay representation.
- Added Resistor component for adjustable resistance in ohms.
- Created RiscVBoard component for visualizing a RISC-V chip.
- Implemented TransistorElements for BJT and MOSFET packages.
- Added Capacitor and CapacitorElectrolytic elements for capacitors.
- Introduced Inductor element for inductor representation.
- Updated index file to export new custom elements.
David Montero