Closes the same gap as the AVR / RP2040 commits — qemu-lcgamboa's UART
transmits the byte over the WebSocket as a 'serial_output' event with no
GPIO toggle, so an oscilloscope on the ESP32 TX pin saw nothing while
real silicon would render the 8N1 frame at the configured baud rate.
Two changes inside Esp32Bridge:
* New `onPinChangeWithTime: (pin, state, timeMs) => void` callback
that hooks the oscilloscope at parity with AVRSimulator /
RP2040Simulator. The 'gpio_change' event now also flows through it
(timestamped with `performance.now()` — QEMU virtual time isn't
surfaced across the wire, but at 1× sim speed the wall-clock skew
is invisible on any practical sweep). This also fixes the broader
issue that ESP32 boards previously couldn't show ANY digital GPIO
activity on the scope.
* `emitUartTxFrame(byte, uart)` synthesizes start + 8 data LSB-first
+ stop transitions at `this.uartBaudRate` (default 115200) on the
UART0 TX pin, mapped per board variant:
esp32 / esp32-devkit-c-v4 / esp32-cam / wemos-lolin32-lite: GPIO1
esp32-s3 / xiao-esp32-s3 / arduino-nano-esp32: GPIO43
esp32-c3 / xiao-esp32-c3 / aitewinrobot-esp32c3-supermini: GPIO21
Backend doesn't expose the live baud rate so we default to 115200
(the Arduino default). Override path: bridge.uartBaudRate = N
once we surface Serial.begin's argument via a backend event.
Wire-up: `bridge.onPinChangeWithTime = getOscilloscopeCallback(boardId)`
inside the three Esp32Bridge construction sites in useSimulatorStore
(setBoardType, addBoard, changeBoard).
The SignalRouter path has been in prod through Phase 2.5 / Phase 3.3
deploys without regressions, so the temporary fallback shipped in
commit 77bf897 can come out. Closes#101.
Backend (esp32_worker.py + esp32_lib_manager.py):
- Stop emitting `ledc_update` from the 0x5000 LEDC callback and from
the polling thread. Only `ledc_duty` (channel + duty_pct) and the
GPIO matrix routing events ship now.
- Drop the channel→gpio reverse-lookup that fed the legacy event.
Frontend:
- Delete `PinManager.broadcastPwm` and `PinManager.pwmListenerPinCount`.
- Delete `makeLedcUpdateHandler` + its `channelGpioMemo`.
- Delete `Esp32Bridge.onLedcUpdate` field + the `case 'ledc_update':`
message handler + the `LedcUpdate` type.
- Strip `this.onLedcUpdate = null` from 14 test mocks.
- Rewrite the `does not call broadcastPwm` guard in
esp32-multi-servo-gpio-matrix.test.ts to assert the method itself
no longer exists on PinManager (stronger regression guard than the
spy version, and doesn't need vi).
- Remove the `PinManager.broadcastPwm fallback` describe block from
esp32-servo-pot.test.ts — every test in it exercised the deleted
fallback path.
Docs (ESP32_EMULATION.md):
- Replace `ledc_update` rows in the events / implementation tables
with the SignalRouter trio (`ledc_duty`, `gpio_routing`,
`gpio_routing_clear`).
- Update the visual flow diagram + the "why this matters" paragraph
to past-tense the broadcastPwm bug.
Tests: 1886 frontend tests pass (the previously-failing
board-kinds-coverage test that needed the new Pi Zero/1/2 kinds is
also green). Backend unit suite: 279 pass, the 11 espidf_real_paths
prereq failures are environment-dependent (need arduino-cli libs in
the local shell) and unrelated.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Replaces the per-peripheral ad-hoc `_ledc_gpio_map` cache with a
proper signal-routing abstraction that mirrors the ESP32 SoC's
IO_MUX + GPIO Matrix exactly. Same idea as real silicon: signal
sources (LEDC channels, RMT, MCPWM, ...) → 40-entry routing table
→ GPIO pins.
Motivation (from user bug report in
velxio.dev/project/5218f9e3-136d-43b3-bba1-6cebde21e1a4): two
ESP32 servos on a solar-tracker visibly oscillated between two
positions instead of moving smoothly when the user changed LDR
sliders. Commit 77bf897 patched it (per-channel gpio memo +
broadcast guard) but the user requested a proper hardware-fidel
architecture, not patches.
Backend:
* `app/services/signal_router.py` — SignalRouter class. Forward
index (gpio → signal_id) + reverse index (signal_id → set of
gpios). `replace_snapshot()` returns the diff for the polling-
fallback path; future C plugin hook becomes a push without
touching this code.
* `app/services/esp32_signals.py` — Signal id constants from
ESP32 TRM (LEDC HS 72-79, LS 80-87) + `ledc_signal_for_channel()`
helper.
* `app/services/esp32_worker.py` — `_ledc_gpio_map` is gone;
`_refresh_ledc_gpio_map` replaced by `_refresh_signal_routing`
which emits `gpio_routing {gpio, signal_id}` events on diff.
The 0x5000 LEDC callback and the LEDC poll thread now emit
`ledc_duty {channel, duty_pct}` (canonical, no gpio) alongside
the legacy `ledc_update {channel, duty, gpio}` for back-compat
during rollout.
Frontend:
* `simulation/SignalRouter.ts` — 1-to-1 TS mirror of the Python
class. Same forward + reverse index; same `pinsForSignal` /
`updateRouting` / `clearRouting` API.
* `simulation/esp32-signals.ts` — Signal id constants, mirror
of the Python module.
* `simulation/Esp32Bridge.ts` — new `onLedcDuty`, `onGpioRouting`,
`onGpioRoutingClear` callbacks; handlers for the new event types.
* `store/useSimulatorStore.ts` — `makeLedcDutyHandler` looks up
pins via `router.pinsForSignal(ledcSignalForChannel(channel))`
and dispatches per pin. `makeGpioRoutingHandler` /
`makeGpioRoutingClearHandler` keep the mirror in sync. Per-board
`signalRouterMap` parallels `pinManagerMap` in lifecycle.
`makeLedcUpdateHandler` (and its memo workaround from 77bf897)
stays wired for back-compat during rollout; removed in a
follow-up commit once prod is verified stable on the new path.
Tests:
* `test/backend/unit/test_signal_router.py` (20 tests) covers
update/clear semantics, idempotency, multi-pin routing,
snapshot diff, channel↔signal-id helpers, and the multi-servo
regression scenario.
* `frontend/src/__tests__/SignalRouter.test.ts` (17 tests) is the
mirror — same scenarios on the TS side.
* `frontend/src/__tests__/esp32-multi-servo-gpio-matrix.test.ts`
(6 tests) drives the end-to-end SignalRouter handler pipeline,
asserts that two servos on GPIO 13/12 via LEDC channels 0/1
move independently (no mirroring), that re-routing carries
cleanly, and — critically — that `PinManager.broadcastPwm` is
never called.
Totals: +700 LOC, 1876 frontend tests pass (was 1853), 278 backend
unit tests pass (was 259).
Docs: ESP32_EMULATION.md §9.2 rewritten with the new architecture
diagram + a runbook for adding future peripherals through the
SignalRouter.
The C plugin hook in qemu-lcgamboa that would push gpio_out_sel
writes synchronously (eliminating the polling race window entirely)
is the next step — kept as a follow-up because the polling-fallback
path here already resolves the routing before each duty event
fires, so the bug is fixed end-to-end. The plugin work removes the
race condition fundamentally.
Closes the remaining gaps in cross-board I2C so any topology of
supported boards (Uno↔ESP32, two ESP32s, Uno↔Uno↔Uno, ESP32-C3
connected to anything, etc.) works end-to-end with all I2C
components including write-only sinks (SSD1306, PCF8574, LCD-I2C).
Implementation (6 phases):
1. **BFS routing in I2CBusManager**: connectToSlave + handleExternalConnect
walk the bridge graph with a visited Set so multi-hop chains
(A↔B↔C with the device on C) resolve transparently. A new
forwarder-device shim is installed at intermediate hops so the
existing handleExternalWrite/Read/Stop machinery routes
through without per-method visited tracking.
2. **Per-peer proxy ownership in Esp32BridgeShim**: replaces the
global _proxiedAddrs Set with _proxiedByPeer Map so concurrent
bridges to the same ESP32 (e.g. wired to both Uno and Pico)
don't wipe each other's proxies on teardown. Interconnect's
per-wire teardown calls clearProxiesForPeer(peerBus) instead of
clearAllProxies.
3. **BFS-aware proxy sync**: syncProxyFromPeer now walks the peer
bus + its transitive bridges, so an ESP32 sees devices on
boards two or more hops away. _peerDeviceLookup keeps a flat
addr → device map for write-forwarding and resync.
4. **Periodic resync (250 ms)**: Esp32BridgeShim runs a setInterval
while any proxy is live, re-dumping each device with
dumpRegisters() and pushing updateProxyI2c only when an XOR-
stride hash changes. This keeps RTC time advancing visible to
ESP32 firmware without flooding the WS pipe with static
calibration dumps. Hash is primed during initial sync so the
first tick doesn't push a redundant identical buffer.
5. **Write-forwarding ProxySlave → peer**: backend ProxySlave
buffers write bytes during the transaction and emits a
`proxy_i2c_complete` event on STOP / repeated-START. Frontend
Esp32Bridge dispatches the event to a new onProxyI2cComplete
callback; the shim replays the byte sequence on the actual
peer I2CDevice via writeByte() + stop(). Makes ESP32 firmware
writes to peer SSD1306 actually repaint the OLED, peer PCF8574
latch updates, peer I2CMemoryDevice register mutations propagate.
6. **ESP32-C3 routed as bridge**: Interconnect.isBrowserSim no
longer claims c3/xiao-c3/c3-supermini — they were already
going through Esp32Bridge per the store's ESP32_RISCV_KINDS
routing, but Interconnect was treating them as browser sims
which broke proxy install. isEsp32Bridge now correctly
includes c3 family + ESP32-S3 + Arduino Nano ESP32.
Defensive: addBoard now disposes any existing shim's proxies
before overwriting simulatorMap entry so test reruns don't leak
timers.
Tests:
- 4 BFS multi-hop tests (i2c-multi-board-slave-gap.test.ts)
- 11 cross-board scenarios + per-peer + write-forward + resync
(i2c-esp32-multiboard-bridge.test.ts)
- 1 real-firmware E2E for write-forward via QEMU (compile +
load + observe proxy_i2c_complete arriving with the byte)
- New sketch fixture: esp32_i2c_write_to_peer.ino
Result: 90 test files / 1295 tests pass / 0 fail.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
- Implemented `i2c-esp32-real-firmware.test.ts` to test ESP32 I2C communication via backend and WebSocket.
- Created `load-example-transitions.test.ts` to ensure proper loading of examples between board-less and board-based contexts.
- Added `CircuitVerificationModal.tsx` to display circuit verification results before running simulations.
- Developed `circuitVerifier.ts` to perform pre-flight checks for circuit safety, identifying potential issues like short circuits and component overloads.
- Introduced minimal ESP32 I2C master sketch `esp32_i2c_writer.ino` for testing I2C transactions.
crypto.randomUUID() is only exposed on secure contexts (HTTPS, localhost,
127.0.0.1, ::1). When Velxio is self-hosted and accessed via a LAN IP over
plain HTTP (e.g. http://192.168.31.139:3080/), crypto.randomUUID is
undefined and any code path that calls it throws TypeError.
This silently broke ESP32 simulation start for self-hosters: the frontend
generates a UUID for the WS client_id when Run is clicked; the throw
rejected the promise before reaching the WS connect, so the backend
never got the start request — no worker spawned, logs empty, simulation
"didn't start" with no visible error.
Same root cause would also break the multi-file editor (createFile,
createFileGroup) on the same LAN-HTTP self-host setup, just less
observably.
Add a single generateUUID() helper that:
1. Uses crypto.randomUUID() when available (secure context fast path).
2. Falls back to crypto.getRandomValues() — which IS available in
non-secure contexts — to build a v4 UUID by hand.
3. Final fallback to Math.random() if even that is missing
(defensive — Web Crypto getRandomValues has been universal for
years).
Replace all 6 crypto.randomUUID() call sites:
- frontend/src/simulation/Esp32Bridge.ts (2 sites — getTabSessionId)
- frontend/src/store/useEditorStore.ts (4 sites — file IDs)
Reported by a self-hoster on OrangePi 5B accessing Velxio via LAN IP.
DevTools console showed:
TypeError: crypto.randomUUID is not a function
at Ph (...) at wh.connect (...) at startBoard (...)
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
User reported the ESP32-CAM + ILI9341 live preview at ~1 frame/min.
Profile: 80×60 preview pushes 9600 SPI bytes per drawRGBBitmap, and
each byte was emitting a full {type:'spi_event'} JSON message over
the worker→backend→WS→frontend pipeline. Per-byte overhead ~150-200µs
in Python (json.dumps + sys.stdout.write+flush dominates) plus
asyncio + WS dispatch. Net: 1.5-2 sec/frame minimum, much worse with
GIL contention.
Fix: buffer MOSI bytes in the worker and emit a single base64-encoded
`spi_batch` message when CS goes HIGH (transaction ended) or the
buffer crosses 4 KiB. ~9600 events/frame collapse to ~3 messages.
backend/app/services/esp32_worker.py:_on_spi_event
- Add _spi_byte_buf bytearray + threading.Lock
- On op==0x00 (byte): append; flush early if buf >= 4096
- On op==0x01 (CS change): flush buffer, then emit the CS event
via the legacy spi_event channel (ePaper / custom chips that
observe CS still get it).
frontend/src/simulation/Esp32Bridge.ts
- New 'spi_batch' message handler decodes b64 and replays each
byte through the existing onSpiByte callback. Parts that
subscribed via simulator.spi.onByte don't notice the protocol
change. The 'spi_event' branch still handles CS changes plus
legacy single-byte payloads for backwards compat.
Now that 38 KB/frame is cheap, restore preview to 160×120 + JPEG
quality 0.35 in the gallery example. Real measured speedup: ~50× on
the QVGA preview demo. Real hardware was never affected — it runs
SPI at 80 MHz and pushes the bitmap in ~4 ms either way.
PSRAM emulation is unrelated to this bottleneck and was left untouched.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
The ILI9341 part simulation only hooked AVR's SPI peripheral. For
ESP32 the simulator is Esp32BridgeShim (no .spi member), so
attachEvents bailed early and the LCD stayed black even though the
firmware was driving SPI traffic correctly.
The QEMU worker already emits per-byte spi_event WS messages
(see backend/app/services/esp32_worker.py::_on_spi_event), and the
Esp32Bridge already had an onSpiEvent hook — but the bridge was
reading msg.data.data (a non-existent field) instead of decoding
the worker's {bus, event, response} format. Fixed.
Two changes:
1. Esp32Bridge.ts: decode the spi_event payload correctly. The
worker encodes byte transfers as `mosi << 8` (op = low byte = 0x00)
and CS-line changes as `((cs<<1)|level) << 8 | 0x01` (op == 0x01).
Added onSpiByte (per-byte) and onSpiCsChange callbacks alongside
the existing onSpiEvent for backwards compat.
2. ComplexParts.ts ili9341Simulation: detect Esp32BridgeShim via
`getBridge()` duck-type check. When present, subscribe to
bridge.onSpiByte and feed bytes into the same processCommand /
processData pipeline used by the AVR path. DC tracking via
pinManager.onPinChange already works for ESP32 because the bridge
fires triggerPinChange on every gpio_change WS event.
Verified end-to-end: ESP32-CAM + ILI9341 example in the gallery now
renders the live webcam preview to the simulated TFT (160×120 RGB565
centered in the 320×240 panel) at ~3-4 fps.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
First open-source end-to-end emulation of the AI-Thinker ESP32-CAM
in QEMU, paired with a browser webcam → firmware bridge so users can
develop camera sketches without hardware. Status: esp_camera_init()
returns ESP_OK; OV2640 chip-id verifies (PID/VER/MIDH/MIDL exactly
match the datasheet); GPIO 25 VSYNC NEGEDGE interrupt enabled by
the upstream driver. Final piece (cam_task accepting frames) is in
progress — descriptor walker fix landed in this commit.
Backend (Python/FastAPI):
- simulation.py: camera_attach/frame/detach WS handlers
- esp32_worker.py: ctypes binding to velxio_push_camera_frame +
feature-detection fallback for older DLLs
- esp32_lib_manager.py: forward camera commands to the worker stdin
- esp-idf-template/main/CMakeLists.txt: esp32-camera headers added
via add_prebuilt_library + REQUIRES driver (resolves i2c_master_*
symbols). LED_BUILTIN=2 fallback for sketches that hardcode it.
Frontend (React/TS):
- EditorToolbar.tsx: ESP32-CAM (and the rest of the ESP32 family)
added to isQemuBoard list — Run button now starts the QEMU bridge
for these boards instead of falling through to the AVR path
- useWebcamFrames.ts: getUserMedia → OffscreenCanvas →
toBlob('image/jpeg') → base64 → WS at ~10 fps
- CameraToggle.tsx: header button with status colors + frame counter
- SimulatorCanvas.tsx: render CameraToggle for esp32-cam boards
- Esp32Bridge.ts: sendCameraAttach/Frame/Detach + chunked btoa
- useSimulatorStore.ts: diagnostic log on compileBoardProgram
- components-metadata.json: regen including esp32-cam component
Submodule pointer:
- wokwi-libs/qemu-lcgamboa → ff8eee0 (camera devices commit on
davidmonterocrespo24/qemu-lcgamboa branch picsimlab-esp32)
Investigation + tests in test/test-esp32-cam/:
- 13 autosearch markdown docs (overview, SOTA, OV2640 spec, DVP/I2S
spec, build blueprint, blockers resolved, descriptor walker fix)
- 5 sketches (camera_init, sccb_probe, dma_smoke, frame_roundtrip,
webcam_demo) + 8 live + WS regression tests
- README with the user-facing flow
.gitignore:
- libqemu-*.dll.{pre-camera,new,bak} (rollback points, regenerated)
- wokwi-libs/esp32-camera/ (clone consumed by arduino-esp32 path,
not part of this repo)
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
- Introduced EPaperPanels.ts to define configurations for various ePaper panels including dimensions, refresh rates, and controller details.
- Implemented SSD168xDecoder.ts to handle the decoding of SPI commands for the SSD168x family of ePaper displays.
- Created EPaperPart.ts to manage the simulation of ePaper panels, integrating with the existing simulator architecture and handling events.
- Added example sketches for 2.13", 2.9", 4.2", and 7.5" ePaper displays, demonstrating basic functionality and text rendering.
- Ensured compatibility with AVR, RP2040, and ESP32 platforms, with appropriate pin configurations for each.
- Modified the index file to reflect the new naming convention for Velxio components.
- Changed JSX declarations to use 'velxio-' prefix for various components.
- Updated component overrides to replace 'wokwi-' with 'velxio-' for logic gates and other components.
- Adjusted SVG generation script to use 'velxio-' prefix for BMP280 and Raspberry Pi components.
- Marked submodules as dirty in QEMU and RP2040 libraries.
- Added .prettierignore and .prettierrc.json for consistent code formatting.
- Introduced InstrumentComponent with support for Voltmeter and Ammeter, including pin information handling.
- Implement `ammeter-waveform.test.ts` to validate AC readings from a sine wave source.
- Create `capacitor-charge-transient.test.ts` to test the charging response of an RC circuit driven by a microcontroller pin.
- Introduce `esp32-rectifier-integration.test.ts` for testing rectifier behavior using QEMU and ESP32.
- Add helper functions in `esp32RectifierE2E.ts` for the rectifier test harness.
- Develop `voltmeter-waveform.test.ts` to ensure correct AC and DC readings from a sine wave source.
- Implement unit tests for waveform statistics in `waveform-stats.test.ts` to validate RMS, mean, peak, and interpolation functions.
- Create `waveformStats.ts` to provide statistical functions for time-domain waveform analysis.
This commit introduces a detailed markdown document outlining the process of simulating DHT22 and HC-SR04 sensors on the ESP32 platform using Velxio's QEMU fork. The documentation covers the context of the simulation, key callbacks, problems encountered, and solutions implemented for both sensors. It includes architectural details, end-to-end testing procedures, and guidelines for adding new GPIO-timed sensors. The aim is to provide maintainers with a thorough understanding of the GPIO logic and the challenges faced during development.
- Implemented _MPU6050Slave and _BMP280Slave classes for I2C communication.
- Enhanced main function to register these sensors and handle I2C events.
- Updated sensor management to support MPU-6050, BMP280, DS1307, DS3231, SSD1306, and PCF8574.
- Added frontend examples for BMP280 weather station and SSD1306 OLED display.
- Modified Esp32Bridge to handle new I2C transaction events.
- Updated ProtocolParts to support ESP32 path for I2C devices.
- Enhanced useSimulatorStore to manage I2C transaction listeners.
- handleRun now auto-compiles for ESP32/QEMU boards when no firmware is
available (same behavior as AVR/RP2040 boards)
- startBoard now reloads compiledProgram into the bridge if _pendingFirmware
was lost (e.g. after a page refresh between compile and run)
- Adds Esp32Bridge.hasFirmware() helper used by the store check
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replace arduino-cli with ESP-IDF 4.4.7 for ESP32 compilation — Arduino-compiled
firmware crashes in QEMU (9-28 reboots) while ESP-IDF boots cleanly (0 reboots).
The new espidf_compiler translates Arduino WiFi/WebServer sketches to native
ESP-IDF C code, compiles with cmake+ninja, and merges into 4MB flash images.
Key changes:
- ESP-IDF compiler: translates WiFi.begin/WebServer to esp_wifi/esp_http_server
- ESP-IDF project template with QEMU-optimized sdkconfig (DIO, 40MHz, no WDT)
- WiFi status parser for ESP-IDF serial logs (wifi_status, ble_status events)
- IoT Gateway HTTP reverse proxy for ESP32 web servers
- WiFi/BLE auto-detection from sketch content + visual status icons
- Static IP 192.168.4.15 matching slirp DHCP first-client range
- Docker: new espidf-builder stage with ESP-IDF 4.4.7 toolchain
- 157 tests covering WiFi/BLE for both ESP32 (Xtensa) and ESP32-C3 (RISC-V)
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Extends MicroPython support (Phase 2) to ESP32 Xtensa boards running on
QEMU. Firmware is downloaded from micropython.org, cached in IndexedDB,
and loaded into QEMU. User code is injected via the raw-paste REPL
protocol after the MicroPython REPL boots.
- Create Esp32MicroPythonLoader.ts for firmware download/cache
- Add raw-paste REPL injection (Ctrl+A → Ctrl+E → code → Ctrl+D) to Esp32Bridge
- Extend loadMicroPythonProgram in store for ESP32 path
- Add ESP32 default MicroPython content (GPIO 2 blink)
- Simplify SerialMonitor Ctrl+C/D to work for all MicroPython boards
- Bundle fallback firmware for ESP32 and ESP32-S3
- Add all ESP32 board variants to SerialMonitor tab maps
Closes#3 (Phase 2)
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
fix: improve session ID handling in Esp32Bridge and update WebSocket close logging
chore: mark subprojects as dirty in QEMU, RP2040, and Wokwi elements libraries
- Added board-agnostic sensor registration methods in RP2040Simulator.
- Enhanced ComplexParts to handle LEDC PWM duty updates for ESP32.
- Updated ProtocolParts to check if the simulator handles sensor protocols natively, delegating to backend if applicable.
- Introduced pre-registration of sensors in useSimulatorStore for ESP32 to prevent race conditions.
- Added tests for ESP32 DHT22 sensor registration flow, ensuring proper delegation and fallback mechanisms.
- Created tests for ESP32 Servo and Potentiometer interactions, verifying PWM subscriptions and ADC handling.
- Implemented ATtiny85 visual component with DIP-8 layout and built-in LED.
- Added Raspberry Pi Pico W web component using official SVG and pin mapping.
- Created RISC-V Board visual component with SOP-20 style and built-in LED.
- Introduced RiscVCore class for minimal RV32I ISA interpreter with memory model.
- Developed RiscVSimulator class for CH32V003-compatible simulator with UART and GPIO support.
- Updated subproject commits for qemu-lcgamboa, rp2040js, and wokwi-elements to dirty state.
- Updated wire structure to replace control points with waypoints for better handling of wire paths.
- Introduced new utility functions for wire hit detection and rendering segments.
- Enhanced wire creation process to support dynamic waypoints and color assignment.
- Implemented a new ESP32 worker for improved simulation handling.
- Added utility functions for generating orthogonal paths and auto-coloring wires based on pin names.
- Improved compatibility with existing projects by ensuring backward compatibility with wire data structures.
- Added detailed logging for GPIO changes, system events, and errors in simulation websocket.
- Improved ESP32 firmware handling by merging individual binaries into a single 4MB flash image.
- Updated ESP32 bridge to handle serial output and GPIO changes with appropriate logging.
- Introduced integration test for ESP32 emulation, covering compilation, WebSocket connection, and event handling.
- Enhanced examples to include ESP32 projects and updated the examples gallery to reflect new board types.
- Refactored simulator store to manage ESP32 bridge and simulator instances more effectively.
- Updated requirements to include esptool for ESP32 firmware management.
- Added ESP32 emulation plan and architecture documentation.
- Created `esp_qemu_manager.py` for managing ESP32 QEMU instances.
- Modified backend API routes to support ESP32 firmware loading and GPIO handling.
- Introduced `Esp32Bridge.ts` for frontend communication with ESP32 instances.
- Refactored simulator store to support multiple boards, including Raspberry Pi and Arduino.
- Created `RaspberryPi3Bridge.ts` for WebSocket communication between frontend and backend for Raspberry Pi.
- Updated QEMU manager to handle multiple serial ports for Raspberry Pi GPIO communication.
- Enhanced SimulatorCanvas to render multiple boards and manage wire routing between them.
- Implemented board picker modal for selecting and adding boards to the canvas.
- Updated editor to support multiple file groups per board.
- Added migration logic for loading old project formats into the new multi-board structure.
- Ensured backward compatibility with existing components and functionality.
David Montero